ÃÌ> >̈œ Ê ÃÌÀÕV̈œ Ã. Contents

Transcription

1 ÃÌ> >̈œ Ê ÃÌÀÕV̈œ à Document Number: ITI Rev. B April 2001 $GYHQWŒ &RPPHUFLDO%XUJODU\DQG +RPH1DYLJDWRU6\VWHP Commercial Burglary Panels 20 Zone Zone Contents About This Manual...1 Special Installation Requirements...1 UL Listed Installations...1 California State Fire Marshall Listed Installations...4 Planning the Installation...4 Panel Types...4 Panel Components...4 Panel Terminals...4 BUS Device Headers... Panel Devices... SuperBus 2000 Touchpads... SuperBus 2000 Modules... SnapCards... Installing the System... Determining the Panel Location...6 Running Wires to the Panel Location...6 System Wire Lengths...6 Mounting the Panel...7 Installing Optional Panel SnapCards...7 Connecting SuperBus 2000 Modules and Touchpads 7 SuperBus 2000 Touchpads...8 SuperBus 2000 Modules...8 Voice Siren 2/70 Volt Converter Card (60-773) 10 Connecting Detection Devices to Panel Zone Inputs 10 Connecting Intrusion Detection Devices...10 Connecting Speakers Connecting Listed Sirens...12 Installing an RJ-31X Phone Jack (13-081)...12 Connecting the Phone Line to the Panel with a DB-8 Cord (49-442)...13 Mounting/Connecting an AC Power Transformer...13 Installing Panel Backup Battery(s)...14 Powering Up the Panel...14 Programming the Panel...14 Using the Downloader Software to Program the Panel...1 Using an Alphanumeric Touchpad to Program the Panel...1 Entering/Exiting Program Mode...1 Using Item Numbers...1 Codes...23 Specific Phone Number Settings...2 Phone Access Settings...29 Zone Settings...31 Home Navigator Panels 20 Zone Zone I/O Settings...34 Accessory Modules...34 Programmable Output Settings...36 Alarm Settings...38 System Settings...39 Miscellaneous Settings...42 Remote Downloader Programming...44 Advent Downloader Programming...44 Installing Line Carrier Devices...44 Programming the Panel House Code...44 Installing X-10 Modules...44 Adding Lights/Devices to Program Memory...44 Testing the System...4 Basic System Commands...4 Testing Panel Backup Battery(s)...4 Testing Hardwire and Wireless Zones/Sensors...4 If a Wireless Sensor Fails the Zone/Sensor Test.46 Testing Outputs and Sirens...46 Testing Lights and Devices...46 Testing Phone Communication...47 Testing Central Station Communication...47 Adjusting Touchpad Display Contrast...47 Troubleshooting...48 Appendix A: System Configuration Worksheets...6 Determining Maximum Panel Wire Length...7 Other System Devices...7 X-10 Modules and Device Settings...8 Partition/Area Descriptions...9 SuperBus 2000 Device Information...60 Zone and Sensor Information...61 Menu Lights and Outputs...67 Programmable Output Type Information...68 Access Codes and Authority Level Settings...69 Item Numbers Index and Record...70 Appendix B: Reference Tables...79 Contact ID Codes and Event Types...96 Additional CID Reporting...99 Smoke and Heat Detector Installation...101

2 Notices FCC Part 1 Information to the User Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the user s authority to operate the equipment. FCC Part 1 Class A (Commercial) This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 1 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense. FCC Part 1 Class B (Residental) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 1 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Install a quality radio or television outdoor antenna if the indoor antenna is not adequate. Reorient or relocate the panel. Move the panel away from the affected equipment. Move the panel away from any wire runs to the affected equipment. Connect the affected equipment and the panel to separate outlets, on different branch circuits. Consult the dealer or an experienced radio/tv technician for help. Send for the FCC booklet How to Identify and Resolve Radio-TV Interference Problems, available from the U.S. Government Printing Office, Washington, D.C Stock Number: FCC Part 68 This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among other information, the FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. The REN is used to determine the maximum number of devices that may be connected to your telephone line. In most areas, the sum of all device RENs should not exceed five (.0). If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. You will be given advanced notice in order to maintain uninterrupted service. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Declaration of Conformity (DoC) Interactive Technologies, Inc. declares that the ITI model no R is in conformity with Part 1 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada Notice The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the user s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company s inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. Caution Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop that is used by the device to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. Load Number: 0.2B AC AVIS: - L étiquette du ministère des Communications du Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d exploitation et de sécurité des réseaux de télécommunications. Le ministère n assure toutefois pas que le matériel fonctionnera a la satisfaction de l utilisateur. Avant d installer ce matériel, l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l enterprise locale de télécommunication. Le matériel doit également etre installé en suivant une méthod acceptée de raccordement. Dans certains cas, les fils intérieurs de l enterprise utilisés pour un service individuel a ligne unique peuvent etre prolongés au moyen d un dispositif homologué de raccordement (cordon prolongateur téléphonique interne). L abonné ne doit pas oublier qu il est possible que la conformité aux conditions énoncées ci-dessus n empechent pas le dégradation du service dans certaines situations. Actuellement, les enterprises de télécommunication ne permettent pas que l on raccorde leur matériel a des jacks d abonné, sauf dans les cas précis prévus pas les tarrifs particuliers de ces enterprises. Les réparations de matériel homologué doivent etre effectuées pas un centre d entretien canadien autorisé désigné par le fournisseur. La compagne de télécommunications peut demander a l utilisateur de débrancher un appareil a la suite de réparations ou de modifications effectuées par l utilisateur ou a cause de mauvais fonctionnement. Pour sa propre protection, l utilisateur doit s assurer que tous les fils de mise a la terre de la source d énergie électrique, des lignes téléphoniques et des canalisations d eau métalliques, s il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissment. - L utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d inspection des installations électriques, ou a electricien, selon le cas. Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l intention des utilisateurs du matériel terminal, doit etre incluse dans l information qui accompagne le materiel homologué. La note pourrait etre rédigée selon le modèle suivant: L indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etre raccordée a un circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut etre constituée de n import somme des indices de charge de l ensemble des dispositifs ne dépasse pas 100. L Indice de charge de cet produit est.

3 About This Manual About This Manual This manual provides information for planning, installing, programming, and testing an Advent Commercial security or Home Navigator system. When necessary, this manual refers you to other documentation included with compatible peripherals. Appendix A: System Configuration Worksheets on page 8 are included for you to record hardware layout and software programming settings. About the User Guide The User Guide contains user worksheets that should be filled out during the installation and programming of the system. Special Installation Requirements Commercial Burglary Panel The commercial burglary panel can be used as an intrusion alarm system. Follow the installation guidelines below: q Some installations may require configurations dictated by city/state codes, insurance, or Underwriter s Laboratories (UL). See the following section UL Listed Installations for various UL component and configuration listings. UL Listed Installations This section describes the minimum requirements for different UL Listed installations. Basic System q Commercial Burglary ( , ) or Home Navigator ( , ) Control Panel q SuperBus 2000 VFD ( ) or LCD ( ) Alphanumeric Touchpad q 24 VAC output, 100 VA Class I, 110VAC, 60 Hz (60-830) or 24 VAC output, 100 VA Class II, 110VAC, 60 Hz (60-823) Line Carrier AC Power Transformer q 17.2 AH or 18.0 AH Backup Battery(s) (60-781) q Backup Battery Cable Assemblies ( [red] and [black]) q UL listed 4 ohm, 1W Speaker q 2K ohm EOL Resistor(s) (49-467) Police Station Connected Burglary Alarm Units and Systems (UL 36) Basic system using Commercial Burg control panel ( or ). The basic system may also include: q Hardwire Magnetic Contact ( or ) or Wireless Learn Mode Door/Window Sensor (60-362). q A SuperBus 2000 Commercial RF Transceiver (60-821) for use with listed wireless signaling devices. q A SuperBus 2000 Printer or Automation Module (60-783) for use with a listed printer. q A SuperBus 2000 Dual Phone Line Module (60-768) for expansion to primary and secondary phone line reporting. System Setup and Programming The system Feature Numbers shall be set as follows in UL 36 listed systems: Table 1: UL 36 Listed System Settings Feature No. Feature Required Setting xx002 Siren Sound Time 16 min. minimum xx003 Entry Delay 4 sec. maximum xx004 Exit Delay 60 sec. maximum yy003 Number of Attempts min. 10 maximum yy004 Communication Format 0 Contact ID xx088 Report Partition/Area Events 1-On xx092 Auto Forced Arming 0-Off xx097 Exterior Siren Arming Verification 0-Off xx098 Local Closing Report Verification 1-On xx102 Exit Delay Reset 0-Off xx108 Local Trouble Annunciation at 1-On LTIME Auto Phone Test Frequency 1 Day AC Stable Time 90 sec. maximum AC Report Delay 6-12 hours Supervisory Time A 4 hours Phone Trouble Disable 0-Off RF Jam Detect Sound Enable 1-On Automatic Panel Backup Battery 1=4 hours Test Interval Commercial/Residential 1-Commercial Detect RF Receiver Failure 1-On Alarm Messages Played at 1-On (High) High Volume Report System Events 1-On #2 Supervisory Time Zone Attribute (all zones) #4 Hardwire Smoke Verify Zone Attribute Set to 4 hours 0-Off xx = Two digit partition number. yy = Two digit non-pager phone number. Local Burglar Alarm Units and Systems (UL 609) Basic system using Commercial Burg control panel ( or ), plus: q Hardwire Magnetic Contact ( or ) or Wireless Learn Mode Door/Window Sensor (60-362). The basic system may also include: q A SuperBus 2000 Commercial RF Transceiver (60-821) for use with listed wireless signaling devices. q A SuperBus 2000 Printer or Automation Module (60-783) for use with a listed printer. 1

4 Special Installation Requirements q A SuperBus 2000 Dual Phone Line Module (60-768) for expansion to primary and secondary phone line reporting. System Setup and Programming The system Feature Numbers shall be set as follows in UL 609 listed systems: Table 2: UL 609 Listed System Settings Feature No. Feature Required Setting xx002 Siren Sound Time 16 min. minimum yy004 Communication Format 0 Contact ID xx088 Report Partition/Area Events 1-On xx092 Auto Forced Arming 0-Off xx097 Exterior Siren Arming Verification 0-Off xx102 Exit Delay Reset 0-Off Auto Phone Test Frequency 1 Day AC Stable Time 90 sec. maximum AC Report Delay 6-12 hours RF Supervisory Time 4 hours No Phone Line 0-Off Enable RF Jam Detect 1-On Automatic Panel Backup Battery 1=4 hours Test Interval Commercial/Residential 1-Commercial Detect RF Receiver Failure 1-On Alarm Messages Played at 1-On (High) High Volume Report System Events 1-On #2-Supervisory Time Zone Attribute (all zones) #4-Hardwire Smoke Verify Zone Attribute Set to 4 hrs 0-Off xx = Two digit partition number. yy = Two digit non-pager phone number. Household Fire Warning System Units (UL 98) Basic system, plus: q Hardwire Smoke Detector (Compatibility Identifier 60-62, 20 per loop maximum): q System Sensor models 2100S, 2100TS, 2100D, 2100TD, 2400, or 2400TH added (learned) into Zone Type 80. q Sentrol models 429AT, 21B, or 21BXT added (learned) into Zone Type 80. The basic system may also include: q SuperBus 2000 Commercial RF Transceiver (60-821) for use with listed wireless signaling devices. q Wireless Smoke Sensor ( or ) added (learned into Zone Type 80. q SuperBus 2000 Printer or Automation Module (60-783) for use with a listed printer. q SuperBus 2000 Dual Phone Line Module (60-768) for expansion to primary and secondary phone line reporting. System Setup and Programming The system Feature Numbers shall be set as follows in UL 98 listed systems: Table 3: UL 98 Listed System Settings Feature No. Feature Required Setting xx002 Siren Sound Time 4 min. minimum xx003 Entry Delay 4 sec. maximum xx004 Exit Delay 60 sec. maximum yy004 Communication Format 0 Contact ID xx08 Enable Police Panic Keys 1-On xx086 Enable Auxiliary Medical 1-On Panic Keys xx087 Enable Fire Panic Keys 1-On xx088 Report Partition/Area Events 1-On xx092 Auto Forced Arming 0-Off xx097 Exterior Siren Arming Verification 0-Off required xx102 Exit Delay Reset 0-Off xx108 Local Trouble Annunciation at 1-On LTIME AC Stable Time 90 sec. maximum AC Report Delay 6-12 hours RF Supervisory Time 4 hours No Phone Line 0-Off Enable RF Jam Detect 1-On Automatic Panel Backup Battery 1-4 hours Test Interval Commercial/Residential 0-Off Residential Detect RF Receiver Failure 1-On Alarm Messages Play at High 1-On High Volume Report System Events 1-On #2-Supervisory Time Zone Attribute (all zones) #4-Hardwire Smoke Verify Zone Attribute xx = Two digit partition number. yy = Two digit non-pager phone number. A (set to 4 hrs. in Feature 17049) 0-Of Household Burglar-Alarm System Units (UL 1023) Basic system plus: q Hardwire Magnetic Contact ( or ) The basic system may also include: q SuperBus 2000 Commercial RF Transceiver (60-821) for use with listed wireless signaling devices. q Wireless Learn Mode Door/Window Sensor (60-362) q SuperBus 2000 Printer or Automation Module 2

5 Special Installation Requirements (60-783) for use with a listed printer. q SuperBus 2000 Dual Phone Line Module (60-768) for expansion to primary and secondary phone line reporting. System Setup and Programming The system Feature Numbers shall be set as follows in UL 1023 listed systems: Table 4: UL 1023 Listed System Settings Feature No. Feature Required Setting xx002 Siren Sound Time 6 min. minimum xx003 Entry Delay 4 sec. maximum xx004 Exit Delay 60 sec. maximum yy004 Communication Format 0 Contact ID xx088 Report Partition Events 1-On xx092 Auto Forced Arming 0-Off xx097 Exterior Siren Arming Verification 0-Off xx102 Exit Delay Reset 0-Off xx108 Local Trouble Annunciation 1-On at LTIME AC Stable Time 90 sec. maximum AC Report Delay 6-12 hours RF Supervisory Time 4 hours No Phone Line 0-Off Enable RF Jam Detect 1-On Automatic Panel Backup Battery 1-4 hours Test Interval Commercial/Residential 0-Off Residential Detect Receiver Failure 1-On Alarm Messages Play at High 1-On High Volume Report System Events 1-On #2-Supervisory Time Zone Attribute (all sensors) #4-Hardwire Smoke Verify Zone Attribute xx = Two digit partition number. yy = Two digit non-pager phone number. A (set to 4 hrs. in Feature 17049) 0-No Central Station Burglar-Alarm System Units (UL 1610) Basic system using Commercial Burglary ( or ) Control Panel, plus: q Hardwire Magnetic Contact ( or ). The basic system may also include: q SuperBus 2000 Commercial RF Transceiver (60-821) for use with listed wireless signaling devices. q Wireless Learn Mode Door/Window Sensor (60-362). q SuperBus 2000 Printer or Automation Module (60-783) for use with a listed printer. q SuperBus 2000 Dual Phone Line Module (60-768) for reporting to multiple phone lines. System Setup and Programming The system Feature Numbers shall be set as follows in UL 1610 listed systems: Table : UL 1610 Listed System Settings Feature No. Feature Required Setting xx002 Siren Sound Time 16 min., minimum xx003 Entry Delay 4 sec., maximum xx004 Exit Delay 60 sec., maximum yy004 Communication Format 0 Contact ID xx088 Report Partition Events 1-On xx092 Auto Forced Arming 0-Off xx097 Exterior Siren Arming Verification 0-Off xx098 Local Closing Report Verification 1-On xx102 Exit Delay Reset 0-Off xx108 Local Trouble Annunciation 1-On at LTIME Auto Phone Test Frequency 1 Day AC Stable Time 90 sec. maximum AC Report Delay 6-12 hours RF Supervisory Time 4 hours No Phone Line 0-Off Enable RF Jam Detect 1-On Automatic Panel Backup Battery 1-4 hours Test Interval Commercial/Residential 1-Commercial Detect Receiver Failure 1-On Alarm Messages Play at High 1-On High Volume Report System Events 1-On #2-Supervisory Time Zone Attribute (all sensors) #4-Hardwire Smoke Verify Zone Attribute xx = Two digit partition number. yy = Two digit non-pager phone number. Digital Alarm Communicator System Units (UL 163) Same as UL 1610 plus: q A UL Listed Exterior Siren. Central Station Reporting A (set to 4 hrs. in Feature 17049) 0-No The panel has been tested with the following central station receivers using Contact ID reporting format: q ITI CS-000 Central Station Receiver. q Sur-Gard Central Station Receiver with models SG-DRL2A and SG-CPM2. q Radionics Model (D6600). 3

6 Planning the Installation California State Fire Marshall Listed Installations The California State Fire Marshall listing has been approved. Planning the Installation This section describes system capabilities to help you get familiar with the system. Appendix A provides planning sheets with tables that let you record the hardware and programming configuration of the system. Fill in all necessary information ahead of time to help prepare for the installation, and retain for your records. It is recommended that no more than 132 wireless sensors be used in any individual Advent system. If 2 or more Advent systems are in close proximity to each other, the total number of wireless sensors for all systems must not exceed 132. Panel Types To plan the installation, find your specific panel type below. The panel type will help determine the system capabilities (dependent upon devices used). Table 6: Advent Panel Types Part Number Panel Components Before installing devices and making wiring connections, familiarize yourself with the main panel components. Figure 1 shows the main component locations for the circuit board. Figure 1. Description Partitions/Areas Circuit Board Main Components Users Input Zones 20Z, Commercial Burglary Panel Z, UL Listings include 36, 609, 98, 1023, 1610 and Gray enclosure. 20Z, Home Nav Panel. UL Listings Z, include 98, 1023 and 163. White enclosure BACKUP BATTERY LUGS POWER LED TERMINAL STRIP MEMORY CLEAR BUTTON PHONE JACK (DB-8 CORD) CONTROL PANEL CIRCUIT BOARD OPTIONAL EXPANSION SNAPCARD INCOMING PHONE LINE TEST LUGS (TIP/RING) OPTIONAL EXPANSION SNAPCARD CONNECT- ORS SUPERBUS CONNECT- ORS (2) 843G0B.DSF Panel Terminals Table 7 describes each of the control panel terminals. Typical system wiring diagrams are provided on the last page of this manual. A) Class 2, Class 3, and power-limited fire alarm circuits must be installed using FPL, FPLR, FPLP, or substitute cable permitted by the National Electrical Code ANSI/ NFPA 70. Wire that extends beyond the cable jacket must be separated from all other conductors by a minimum of 1/4-inch or by a nonconductive barrier. OR (B) Class 2, Class 3, and power-limited fire alarm circuit conductors must be installed as Class 1 or higher circuits. Table 7: Panel Terminal Strip Connections Terminal Name Used for 1 24 VAC 2 24 VAC 3 GND VDC INT BELL EXT SIREN RTN EXT SIREN OUT EXT SIREN IN VOICE SIREN VOICE SIREN 11 ZONE COM 12 GPI/O 1 24 VAC, 100 VA power transformer connection. 24 VAC, 100 VA power transformer connection. Common ground connection for sirens, general purpose outputs 1-6, etc. Interior bell (+), and misc. DC power supply, 12 maximum load (includes Bus 1 and Bus 2 headers) Current limited. Negative (-) side of bell connection mA (sink) maximum. Positive (+) side to +12 VDC terminal 4. Connect multiple interior bells in parallel 1. Negative (-) external siren drive return connection 1. Positive (+) external siren power output connection A maximum load 1. Or ma maximum. Positive (+) external siren drive input connection A or ma maximum. Normally connected to +12 VDC terminal 4 or other siren voltage source 1. One side of voice siren (speaker) connection. Other side to VOICE SIREN terminal One side of voice siren (speaker) connection. Other side to VOICE SIREN terminal 9 2. Common return connection for general purpose inputs 1 7, sensors, etc. 13 GPI/O 2 General purpose hardwire input. GPI/Os 14 GPI/O can be programmed for use as a hardwire contact input (2.0K ohm EOL 1 GPI/O 4 resistor) or a control relay driver output 16 GPI/O (200 ma sink at 12 VDC maximum). 17 GPI/O 6 18 INPUT 7 Hardwire input Unused 4

7 Installing the System Table 7: Panel Terminal Strip Connections Terminal Name Used for 20 GND Common ground 21 +SMOKE (+12V DC SW) 22 -SMOKE Backup Battery 1 Backup Battery 2 +RED -BLACK +RED -BLACK BUS Device Headers Both bus device headers allow you to use SuperBus 2000 touchpads, modules, and devices. Each header can handle up to 31 devices for a total of 62 devices per panel. Table 8 describes the bus device headers. Panel Devices Positive (+) side of 2-wire, 12 VDC smoke loop. (Smoke and heat sensor DC power supply.) Switched ma maximum (in alarm). Negative (-) side of 2-wire, 12 VDC smoke loop. Positive (+) side of panel backup battery one. 1.6A source maximum. Source current limited. Negative (-) side of panel backup battery one. Positive (+) side of panel backup battery two. Source current limited. Negative (-) side of panel backup battery two. ÊFor supplementary use only. ÊFour to eight ohm maximum load between terminals 9 and 10. Table 8: BUS 1 and BUS 2 Headers Pin Name Used for 1 (Red) +12V DC SuperBus DC power supply ma maximum. Current limited. 2 (Green) BUS A SuperBus communication connection. 3 (White) BUS B 4 (Black) GND SuperBus common ground connection. Devices that you can attach to the panel include SuperBus 2000 modules and SnapCards. SuperBus 2000 Touchpads The following touchpads provide complete system programming and operational control. q SuperBus x20 LCD Touchpad: Provides system programming and operation control. Large display shows system messages that prompt users for information when needed and indicates system status. q SuperBus x20 VFD Touchpad: Provides system programming and operation control. Large fluorescent display shows system messages that prompt users for information when needed and indicates system status. SuperBus 2000 Modules The following modules expand the system as described below: q SuperBus 2000 Commercial RF Transceiver Module: The transceiver enables the use of wireless zones. When the transceiver is installed you may use a combination of wireless and hardwire zones to reach the panel maximum. q SuperBus Z Input Module (HIM): Provides eight additional hardwire zone inputs. q SuperBus Relay Output Module (HOM): Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events. q SuperBus 2000 Dual Phone Line Module: Allows for the use of two phone lines. In the event a primary phone line fails, a secondary line will be used. q SuperBus 2000 Printer Module: Allows you to connect a printer to the panel. q SuperBus 2000 RS-232 Automation Module * : The SuperBus 2000 RS-232 Automation module allows you to connect an Advent panel to a compatible automation system. Once connected, the module will enable the automation system to interpret panel system status. q SuperBus 2000 LED Display Module (LED Driver Board)*: Uses LEDs to display system and devices status. Up to 16 SuperBus 2000 LED display or terminal boards may be connected to one driver board. q Voice Siren 2/70 Volt Converter Card*: Adds high voltage siren audio output capability. SnapCards The following SnapCards expand the system as described: q 8Z Input SnapCard: Provides eight additional hardwire zone inputs, of which two are dedicated for using 2-wire smoke detectors (residential listings only). q 4 Output SnapCard: Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control. q 4Z Input/2 Output Combo SnapCard: Provides three hardwire zone inputs, one two wire smoke detector loop, and two outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control (residential listings only). Installing the System This section describes how to install the system control panel. Before starting the installation, plan your system layout and programming using the worksheets provided in Appendix A on page 8. Installing the system consists of the following: q Determining the panel location (p. 6). q Running wires to the panel location. q System wire lengths (p. 6). q Mounting the panel (p. 7). q Installing optional snapcards (p. 7). q Connecting SuperBus 2000 modules and touchpads (p. 7). q Connecting detection devices to panel zone inputs (p. 10). * Not investigated by UL.

8 Installing the System q Connecting speakers (p. 11). q Connecting sirens (p. 12). q Installing an RJ-31X Phone Jack (p. 12). q Connecting the phone line to the panel with a DB-8 cord (p. 13). q Mounting/connecting an AC power transformer (p. 13). q Installing the backup battery(s) (p. 14). q Powering up the panel (p. 14). Determining the Panel Location Before permanently mounting the panel, determine the panel location using the following guidelines: q Centrally locate the panel in relation to detection devices whenever possible to help reduce wire run lengths and labor. q Avoid running wires parallel with electrical wiring, or fixtures such as fluorescent lighting, to prevent wire runs from picking up electrical noise. q Locate the panel where the temperature will not exceed 120 F (49 C) or fall below 32 F (0 C). q If optional wireless transceiver module is used, avoid locations near excessive metal such as HVAC ducts, foil wallpaper, gas/water pipes, and electrical wiring. q Mount the panel at a comfortable working height (about 4 to inches from the floor to the bottom of the panel, as shown in Figure 2). q Allow 6.-inches to the right (or left) of the panel for wiring, phone jack, and optional module mounting. q Allow at least 24-inches in front of the panel for access to panel components. 4-" FLOOR Figure 2. 1" PANEL 21." 21." NOTE ALLOW AT LEAST 24" IN FRONT OF PANEL FOR ACCESS TO PANEL COMPONENTS PHONE JACK AND OPTIONAL MODULE MOUNTING AREA Determining Panel Location 843G06B.DS4 Running Wires to the Panel Location Once you have determined the best possible panel location, run any necessary wires for the: q power transformer, q phone line(s), q sirens/speakers, q SuperBus 2000 alphanumeric touchpads, q hardwired zones, q output devices, q Optional SuperBus 2000 modules (such as Dual Phone Line, Printer Modules, etc.). System Wire Lengths The total system wire length allowed can vary depending on devices powered by the panel, the wire length between devices and the panel, and the combined wire length of all devices. q Table 9 describes wiring recommendations for various panel components. For devices where no recommended wire lengths are stated, or several devices share the same wire runs to the panel, please see Table A2 on page 7 to determine wire lengths based on current draw and resistance. q Use 18-gauge wire for all commercial installations. q Listed auxiliary power supplies may be used to reach the 4000ft maximum wire length for SuperBus modules. Please see Table A2 on page 7 to determine wire lengths based on the module(s) used. Table 9: Wire Recommendations Device AC Power Transformer Earth Ground Telephone Detection Devices Output Devices 2-Wire Smoke Detectors Sirens, Piezos, and Speakers SuperBus x20 LCD Alphanumeric Touchpad SuperBus x20 VFD Alphanumeric Touchpad SuperBus 2000 Commercial RF Transceiver Max. Wire Length to Panel 2-conductor, 18-gauge (located in cabinet) Single conductor, 14-gauge, 2 feet maximum Wire Type Stranded Solid or Stranded Phone grade, 22-gauge Solid or Stranded 2- or 4-conductor, Stranded 22-gauge, 0-ohms resistance per zone including device 18-gauge, 00 ft. maximum 2-ohms per zone (including detection device resistance) 2-conductor, 18-gauge, 00 feet maximum 22 ga. 00 ft. 18 ga ft. 22 ga. 00 ft. 18 ga ft. 22 ga. 120 ft. 18 ga ft. Stranded Stranded Stranded Stranded Stranded Stranded 6

9 Installing the System Table 9: Wire Recommendations (Continued) Device SuperBus Z Input Module SuperBus Relay Output Module SuperBus 2000 Dual Phone Line Module SuperBus 2000 Printer Module SuperBus 2000 RS 232 Automation Module* SuperBus 2000 LED Driver Board* Mounting the Panel Max. Wire Length to Panel 22 ga. 170 ft. 18 ga ft. 22 ga. 200 ft. 18 ga. 00 ft. 22 ga. 30 ft. 18 ga. 900 ft. 22 ga. 100 ft. 18 ga ft. 22 ga. 100 ft. 18 ga ft. 22 ga. 7 ft. 18 ga. 200 ft. Wire Type Stranded Stranded Stranded Stranded Stranded Stranded 4 Input/2 Output SnapCard N/A N/A 8Z Hardwire Zone Expander N/A N/A SnapCard 4 Output SnapCard N/A N/A * Not investigated by UL. Use the following procedure to mount the panel to the wall or wall studs using the supplied mounting hardware and the panel mounting holes shown in Figure 3. &$87,21 Make sure you are free of static electricity whenever you work on the panel with the cover open. To discharge any static, first touch the metal panel chassis, then stay in contact with the chassis when touching the circuit board. Using an approved grounding strap is recommended. 1. Open the panel door and remove the panel circuit board, accessory kit, and packing material. 2. Put the circuit board from the packing in a safe static free location. 3. Remove the desired panel wiring knockouts. 4. Mount the optional key lock (if used) into the panel door.. Place the enclosure in position against the wall. Make sure enclosure is level and mark the locations of the two mounting holes and two keyhole mounting holes. Remember to leave room near the enclosure for any optional modules. 6. Use the appropriate mounting anchors and screws for your application. Partially insert screws into the two anchors at the two top keyhole locations, and then hang the panel chassis on the two screws. 7. Recheck level, insert the two lower screws, and then tighten all four mounting screws. 8. Route all wires to the panel. 9. Install the panel circuit board, using the five supplied board mounting screws. Figure 3. Mounting the Panel and Circuit Board Installing Optional Panel SnapCards q 8Z Input SnapCard (60-77). q 4 Output SnapCard (60-78). q 4Z Input/2 Output Combo SnapCard (60-76). The SnapCard Connectors shown in Figure 4 allow for the installation of two expansion SnapCards. Carefully install a SnapCard onto the desired SnapCard Connector and secure it in place with the two screws included with the card. Figure , $ , )! " 2 ; 9, - ; , 6 6 7, / ) / 2 ) ; 9, ) * ) 4, * ) * ) ; I CONTROL PANEL CIRCUIT BOARD SECONDARY EXPANSION CARD CONNECTOR ) , ) / 4 7, + 0 ) / / / 0 - & # "! / % *, PRIMARY EXPANSION CARD CONNECTOR EXPANSION CARD ALIGN BOARD HOLES WITH STANDOFFS (2) Installing an Expansion SnapCard into one of the two SnapCard Connectors Connect all necessary input and/or output wiring using the Installation Instructions included with the SnapCard(s). Connecting SuperBus 2000 Modules and Touchpads Up to 31 SuperBus 2000 devices (combinations of touchpads and modules) can be used on each of the two SuperBus connectors for a total of up to 62 devices. These modules connect to the panel via a 4-wire digital data bus and may 7

10 Installing the System be located inside, next to, or away from the panel cabinet (see Figure ). The panel cabinet may accommodate up to: q 3 SuperBus 2000 input/output modules, q 1 Voice Siren 2/70 Volt Converter Card, * q and 2 AC Power Transformers. To wire SuperBus 2000 devices to the SuperBus connectors you must use the Panel SuperBus Wiring Harnesses (49-462) included with the accessory kit. You must splice all SuperBus 2000 module and touchpad wiring to the wires on these harnesses. Both SuperBus connectors are the same, and any combination of SuperBus devices (up to 31) may be wired to either connector. When all of the SuperBus 2000 devices are wired, plug each wiring harness into a SuperBus connector. The +12 VDC (RED) lead on the SuperBus wiring harness is current limited to 60 ma. If the total current draw for all devices on either SuperBus connector exceeds 60 ma, another power source must be used such as Terminal 4 (+12V) or an external +_12V power supply. WIRES FOR HARDWIRE INPUT OR KEYSWITCH (SEE SPECIFIC TOUCHPAD INSTALL INSTRUCTIONS FOR INFORMATION AND RESTRICTIONS) YELLOW PANEL SUPERBUS WIRING HARNESS SPLICE TO ADDITIONAL SUPERBUS TOUCHPADS AND/OR MODULES BLACK (GND) WHITE (BUS B) GREEN (BUS A) RED (+12 VDC) SPACE FOR 2ND TRANSFORMER Figure A.DSF SPACE FOR 3RD HIM/HOM/DUAL PHONE LINE MODULE Mounting Devices in Panel Cabinet PANEL CABINET (COVER NOT SHOWN) MOUNTED TRANSFORMER MOUNTED HIM/HOM/DUAL PHONE LINE MODULE MOUNTED VOICE SIREN 2/70 VOLT CONVERTER CARD SPACE FOR 2ND HIM/HOM/DUAL PHONE LINE MODULE SuperBus 2000 Touchpads q 2x20 LCD Alphanumeric Touchpad ( ). q 2x20 VFD Alphanumeric Touchpad ( ). Connect SuperBus 2000 touchpads to the desired SuperBus connector as shown in Figure 6. For mounting instructions please see the specific touchpad Installation Instructions. Figure 6. SuperBus 2000 Modules Connecting SuperBus 2000 Alphanumeric Touchpads Commercial RF Transceiver Module q Commercial RF Transceiver Module in Plastic Case ( ). Connect the transceiver to the panel as shown in Figure 7. TO OTHER SUPERBUS DEVICES BLACK WHITE GREEN RED NOT USED TOUCHPAD WIRING HARNESS TAB SLOT (3) 84326A.DSF SUPERBUS COMMERCIAL RF TRANSCEIVER MODULE +12 VDC BUS A SPLICE BUS B GND PANEL SUPERBUS WIRING HARNESS Figure G0A.DSF Connecting SuperBus 2000 Commercial RF Transceiver module * Not investigated by UL. 8Z Input Module (60-774) Connect the SuperBus Z Input Module to the panel as shown in Figure 8. Connect all necessary input wiring 8

11 Installing the System using the Installation Instructions included with the module Dual Phone Line Module (60-768) Connect the SuperBus 2000 Dual Phone Line Module to the panel as shown in Figure 10. Connect all other phone wiring using the Installation Instructions included with the module. SUPERBUS DUAL PHONE LINE MODULE TERMINAL STRIP ZONE 2 ZONE COMMON ZONE 1 ZONE 8 ZONE COMMON ZONE 7 ZONE 6 ZONE COMMON ZONE ZONE 4 ZONE COMMON ZONE VDC 1 BUS A 2 BUS B 3 GND 4 BLACK (GND) TO OTHER SUPERBUS DEVICES BLACK WHITE GREEN RED SPLICE WHITE (BUS B) GREEN (BUS A) RED (+12 VDC) Figure 8. PANEL SUPERBUS WIRING HARNESS A.DSF Connecting a SuperBus Z Input Module PANEL SUPERBUS WIRING HARNESS G0A.DSF Figure 10. Connecting a SuperBus 2000 Dual Phone Line Module 4-Relay Output Module (60-770) Connect the SuperBus Relay Output Module to the panel as shown in Figure 9. Connect all necessary output wiring using the Installation Instructions included with the module. Printer Module q Printer Module in Plastic Case (60-783). Connect the SuperBus 2000 Printer Module to the panel as shown in Figure 11. Connect all other printer wiring using the Installation Instructions included with the module SUPERBUS PRINTER INTERFACE MODULE TERMINAL STRIP +12 VDC BUS A BUS B GND NO 4 COM 4 NC 4 NO 3 COM 3 NC 3 NO 2 COM 2 NC 2 NO 1 COM 1 NC 1 ZONE COM ZONE BLACK (GND) WHITE (BUS B) GREEN (BUS A) RED (+12 VDC) TO OTHER SUPERBUS DEVICES BLACK WHITE GREEN RED SPLICE PANEL SUPERBUS WIRING HARNESS A.DSF PANEL SUPERBUS WIRING HARNESS Figure 11. Connecting a SuperBus 2000 Printer Module RS-232 Automation Module * A.DSF Connect the SuperBus 2000 RS-232 Automation Module to the panel as shown in Figure 12. For all other connections please see the module Installation Instructions. Figure 9. Connecting a 4-Relay Output Module * Not investigated by UL. 9

12 Installing the System * 7 ) 7 6 ) 6 1, ) , + * 7 ) * 7 * /, Separate in and out conductors must be used at each speaker. Do not loop a single wire around each terminal. Connecting Detection Devices to Panel Zone Inputs! " Connecting Intrusion Detection Devices * ) + /, * 7 * / * 7 ) 4 -, 8, + For information on programming and configuring detection devices, please see Zone Settings on page 22. For information on mounting and installing devices please see the Installation Instructions included with the device. 2 ) * / 0 ) 4 - " ' " $ & & " # / ), General Inputs Figure 1 shows the typical wiring for N/C and N/O door/ window intrusion detection. Figure 12. Connecting a RS-232 Automation Module Voice Siren 2/70 Volt Converter Card (60-773) * Mount the card in the panel cabinet in the area shown in Figure, and as described in the specific Installation Instructions. Wire the card to the panel and speakers as shown in Figure volt wiring and supervision is shown. For 2 volt wiring, connect speakers to COMMON and 2V terminals, then jump +SUPERVISION to 2V terminal. PANEL TERMINALS I/O COM PANEL TERMINALS ZONE 1* NORMALLY CLOSED (N/C) CONTACTS IN SERIES I/O COM ZONE ** ZONE 6** NORMALLY OPEN (N/O) CONTACTS IN PARALLEL VOICE VOICE SIREN SIREN SUPER- VISION VOICE SIREN CONVERTER CARD TERMINALS 70V 2V COM- MON 2k OHM EOL RESISTOR (LOCATE AT LAST DEVICE) OHMS UL-LISTED SPEAKERS (PARALLEL) 971g03d.dsf 2K OHM WATT EOL RESISTOR ASSEMBLY (LOCATE AT LAST DEVICE) Figure 13. Connecting the Voice Siren 2/70 Volt Converter Card *OR TO ANY GP I/O PROGRAMMED AS A NORMALLY CLOSED INPUT. Figure 14. Installing Intrusion Detection Devices Connecting 2-Wire Smoke Detectors Panel terminals 21 and 22 are set up to accept the following 12 VDC 2-wire smoke detectors. q System Sensor models 2100S, 2100TS, 2100D, 2100TD, 2400, or 2400TH. q Sentrol (ESL) models 429AT, 21B, or 21BXT. Panel terminals 21 and 22 can handle up to 20 smoke detectors with 120 ua maximum idle current per detector. Maximum total loop current allowed in alarm condition is 100 ma. Connect one or more 2-wire smoke detectors to the panel as shown in Figure 16. * Not investigated by UL. 10

13 Installing the System 2 ) ) ` , " ' " $ % + ) 6 - ) 6 ) 6, ) ) ' ` 1 6 -, ) 6, " ' " $ % 1 6 ) ) 6 ) 6, ` 7-1 ), 7 6, ) 1 ; + 0 ) , / - 6 0, ; - & ) - 4! $ # 9 ) 6 6 4! $! 9 ) & ) ) 4 ) - " 0 2 ) ) ' Figure 1. Connecting 2-Wire Smoke Detectors Connecting Speakers The panel provides one speaker driver output for intrusion (steady), fire (temporal 3), and auxiliary (on-off-on-off) alarm sounds. The speaker output is used for partition/area 1 only. The output can drive a single 8-ohm speaker or multiple speaker circuit of 4- to 8-ohms (as shown in the following speaker wiring diagrams). Comparable speakers are described below and on the following page. &$87,21 To avoid damage to the panel speaker output, do not make speaker connections with the panel powered up. 1-Watt Speaker (13-060) 30-Watt Speaker (13-061) Use this speaker for interior siren applications such as status and voice. When wiring multiple speakers, the total impedance for all speakers must be between 4 and 8 ohms. Connect the speaker(s) to the panel as shown in Figure 16. For mounting instructions please refer to the Installation Instructions included with the speaker.! # 8 + ) 2 ) ) 4 1 -, % + ) 6 - ) 6, , " ' " $ % + ) 6 - ) 6 ) 6, Figure 16. Connecting 1- and 30-Watt Interior Speakers Hardwire Interior Speaker and Piezo (60-22) * Use this speaker for interior siren applications. Connect the speaker to the panel as shown in Figure 17. When wiring multiple speakers, stay between 4 and 8 ohms. 0 ) 4, ) - 4 ), 2 1- $ # " ' " $ % + ) 6 - ) 6 ) 6, , * ) +! # 8 + ) 2 ) ) 4 1 -, % + ) 6 - ) 6, , - 6 ) 1 " # ' 2 ) ) 8, * & # "! " ), Figure 17. Connecting a Hardwire Interior Speaker and Piezo Hardwire Interior Speaker (60-28)* Use this speaker unit for interior siren applications. Connect 1 speaker to the panel as shown in Figure 18. Connect multiple speakers to the panel as shown in Figure 19. * Not investigated by UL. 11

14 Installing the System &$87,21 Connect only the large speaker to panel terminals 9 and 10 as shown. The smaller speaker cannot handle the output of terminals 9 and 10 and should not be connected to avoid damaging the speaker. PANEL TERMINALS +12 VDC FOR SUPPLEMENTARY USE ONLY INT. BELL EXT. SIREN/HORN RTN OUT IN 0 ) 4, , 7 ) 2 - ) - 4 $ # &, - 6 ) 1 BLACK RED " ' " $ % + ) 6 - ) 6 ) 6, Figure 18. Connecting the Hardwire Interior Speaker with Dual Speakers to the Panel Figure 19. Connecting Multiple Hardwire Interior Speakers w/dual Speakers to the Panel Connecting Listed Sirens ' ' & # "! /!! ), " Connect a listed exterior siren for partition/area 1 to the panel as shown in Figure 20. Interior and exterior sirens for other partitions/areas must be mapped to SnapCard, Super- Bus module or panel onboard outputs. Refer to program item 000 on page ! # 8 + ) 2 ) ) 4 1 -, % + ) 6 - ) 6, ) ) " ' " $ % + ) 6 - ) 6 ) 6, ) ), - 6 & # "! % # *, ) 1! # 8 + ) 2 ) ) 4 1 -, % + ) 6 - ) 6, HARDWIRE B.DSF EXTERIOR SIREN Figure 20. Connecting the Hardwire Exterior siren to the Panel (partition/area 1) Installing an RJ-31X Phone Jack (13-081) Use the following guidelines when installing an RJ-31X phone jack for system control by phone and central station monitoring. q Locate the RJ-31X jack (CA-38A in Canada) no further than five feet from the panel. q The panel must be connected to a standard analog (loopstart) phone line, that provides around 48 volts DC (onhook or idle). The panel cannot be used on a digital or PBX phone line. These systems are designed for digital type devices only, operating anywhere from volts DC and up. The panel uses an analog modem and does not have a digital converter, adapter, or interface to operate through such systems. q For full line seizure, install an RJ-31X phone jack on the premises phone line so the panel is ahead of all phones and other devices on the line. This allows the panel to take control of the phone line when an alarm occurs, even if the phone is in use or off-hook. q If an analog line is not available, contact your customer s telecommunications specialist and tell him/her you need an analog line off the phone switch (PBX mainframe) or a 1FB (standard business line). Connecting the panel to an analog line off the phone switch places the panel ahead of the phone system, preventing panel access from phones on the premises. However, the panel can still be accessed from off-site phones. To connect a phone line to the panel using an RJ-31X/CA-38A jack: 1. Run a 4-conductor cable from the TELCO protector block to the jack location (see Figure 21). 2. Connect one end of the cable to the jack. 3. At the TELCO protector block, remove the premises phone lines (lines from phone jacks on premises) from the block and splice them to the black and white (or yellow) wires of the 4-conductor cable. 4. Connect the green and red wires from the 4-conductor cable to the A (+) and B (-) posts on the block (see Figure 21). 12

15 * / ; - Installing the System. If desired, add phone jack tamper by splicing the black and yellow phone jack wires to the panel terminals and adding a 2.0K ohm EOL resistor between the blue and orange phone jack terminals as shown in Figure Check the phones on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to Troubleshooting on page 0 if problems persist. 3. Check the phones on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to Troubleshooting on page 0 if problems persist. (PANEL CIRCUIT BOARD) 4! : + )! & ) ) + PHONE JACK * 4 / 4 ; * 7 4 / ; - * / 4 4 -, " ' " $ % ) ) + 6 ) 2-4 BRN DB-8 CORD PLUG GRY * ) + 4 -, * + ) * / 4 4 -, ; - 9 / ,, 6 2 ) ) 6 2 ) ) 4 6 ) ; / ) ) 2 4 / 4 ) -, ) ) ) ) + 6 ) & # "! / ), Figure 21. Installing an RJ-31X Phone Jack Connecting the Phone Line to the Panel with a DB-8 Cord (49-442) After installing the RJ-31X jack, you are ready to connect the phone line to the panel. To connect the DB-8 cord to the panel terminals and RJ-31X jack: 1. Insert one end of the DB-8 cord plug into the RJ-31X (see Figure 22). 2. Insert the other end of the DB-8 cord plug into the phone jack on the Advent panel circuit board (see Figure 22) A.DSF Figure 22. Connecting the DB-8 Cord to the Panel and RJ-31X Jack Mounting/Connecting an AC Power Transformer Use the following AC power transformers with Advent panels: q 24 VAC output, 100 VA Class I, 110VAC, 60 Hz (60-830). q 24 VAC output, 100 VA Class II, 110VAC, 60 Hz (60-823) Line Carrier AC Power Transformer. 1. Mount the transformer in the cabinet at one of the two locations shown in Figure. Transformer load (secondary) terminals must face the center of the enclosure. 2. Secure the transformer to the cabinet using the threaded standoffs and supplied hex nuts. 3. Route the AC power transformer cord or wires through one of the knockouts. The AC supply is non-power limited. It must be separated from all power limited wiring in the cabinet by at least 0.2 and wired using a separate knockout. 4. Wire the AC power transformer to the panel as shown in Figure 23. GRN RJ-31X JACK RED 13

16 Powering Up the Panel TO 110 VAC 60 HZ CIRCUIT TO 110 VAC 60 HZ OUTLET " ' " & " " ' " % $ SPLICE LINE CLASS 1 24 VAC 100 VA LOAD BUILT-IN CIRCUIT BREAKERS OR LINE CLASS 2 24 VAC 100 VA LOAD 4 -, * ` 2 ) - * ) ` * ) ; 8 7 / 4 -, * ) * ) ; ` * ) + $ % & 1 / - * ) ; ), ) 4, 4 Figure 23. Wiring an AC Power Transformer to the Panel Installing Panel Backup Battery(s) The panel uses from one to three rechargeable, sealed 12V lead-acid backup batteries (60-781). When replacing batteries, always replace with the same battery type and size. To install (or replace) backup battery(s): 1. Make sure the panel AC power is off or disconnected. &$87,21 While AC power is applied to the panel, the charging voltage is present at the battery leads. 2. Verify all wiring at the panel and devices for correct terminations. 3. Place the battery in the lower left or right portion of the panel enclosure, with the terminals facing up. 4. Connect the black battery wire(s) from the panel circuit board negative (-) battery spade lug(s) (located on the left side of the board) to the negative (-) battery terminal (Figure 24).. Connect the red battery wire(s) from the panel circuit board positive (+) battery spade lug(s) to the positive (+) battery terminal. 6. On three battery installations, wire the third battery in parallel (positive to positive and negative to negative) with either of the two sets of battery spade lugs on the panel.! :$1,1* 24 VAC 24 VAC 1 2 PANEL TERMINALS 24 VAC 24 VAC A.DSF Never short-circuit or reverse the battery wires. Possible injury to you and/or permanent damage to the panel and battery could result. 4 -, 8 * ) * ) ; $ % & * ) +, 7 ) * ) ; ) * ) ; ) , * ) ; 1 2 ) 4 ) ) ; * ) ; 7 1 / ),, 16 1 ) " ' " % $ ), " ' " % $ * ) ; + ) * - Figure 24. Connecting Backup Battery(s) Powering Up the Panel After connecting and wiring all devices to the panel, you are ready to power up the panel. To power up the panel: ` 4 -, 8 * ) * ) ; 1. If you have not already done so, connect the backup battery(s). 2. Depending on your transformer, q Plug the transformer into an outlet not controlled by a switch, q or apply power to the circuit which the transformer is connected to. 3. Wait about 30 seconds and note the following: q The green power LED (located on the circuit board) turns on and stays on. q Alphanumeric touchpads should display PARTITION 1 SECURITY IS OFF. If the power LED is off or flashing, or if touchpads don t display anything, remove panel power, disconnect the backup battery(s) and see Troubleshooting on page 48. Programming the Panel $ % & " ' " & " " ' " % $ " ' " & " " ' " % $ * ` 2 ) - * ) * ) ; 7 / The panel can be programmed using downloader software or an alphanumeric touchpad connected to the panel. The system interface is menu-driven and self-prompting. It will automatically request access codes and data if required. 4 -, * ) + 4 -, * ) + ` ` & # "! % ' *, 14

17 Programming the Panel Using the Downloader Software to Program the Panel * With a personal computer, modem, phone cables, and ITI Advent Downloader software, you can quickly and efficiently download previously selected programming to the panel via a phone line connection. You can also upload panel programming to the software for your records or for copying to another similar installation. For details on using the downloader software, refer to the Advent Downloader User s Manual shipped with the software. For detailed instructions on preparing the panel for downloading, refer to Remote Downloader Programming on page 46. Using an Alphanumeric Touchpad to Program the Panel In program mode, touchpad buttons let you navigate through installer programming menus for configuring the system. Table 10 describes the touchpad button functions in program mode. Table 10: Alphanumeric Touchpad Button Programming Functions Button Programming Function # Confirms data entry. * Press to undo, cancel data/selection, or return to previous menu. 0 thru 9 Enter numeric values wherever needed. 0 & 1 Select off (0) or on (1) wherever needed. Entering/Exiting Program Mode Entering program mode is done using an installer code. The system can only be placed in program mode when all partitions/areas are disarmed. To enter program mode: 1. Make sure the system is disarmed in all partitions/areas. 2. At a touchpad, press 8 and the touchpad displays SYSTEM MENU. 3. Press 0 and the touchpad displays ENTER YOUR CODE. 4. Enter your INSTALLER ACCESS CODE (0123 is default) and the touchpad shows PROGRAM MENU then ENTER ITEM NUMBER. Enter the desired item number. To exit program mode: q Press * repeatedly. Using Item Numbers When prompted, entering an Item Number will jump you to the setting associated with the number. Once at the setting you may view or change setting attributes. After changing attributes press #Áto confirm, then you may exit programming (*) or enter another item number. Table 11 describes the setting type and range/description of all system item numbers. Table 11: Item Number Descriptions Setting Type Range and Description Partition/Area xx001 xx12 (xx = partition 01 08) Global/System Phone Number yy001 yy00 (yy = phone 19 24) zz001 zz016 (zz = phone/pager 2 40) Zone Utilities SuperBus Utilities , Display Text Utilities Miscellaneous Utilities System settings are explained below and on the following pages. They appear as follows: EH A 6 E A N N, A B= K J $ / ) * - 4, - ) 7 6 System settings in this manual appear in the same order as you would see them in Advent Downloader software. This is done to eliminate confusion whether you are programming from a touchpad or the downloader. If you prefer, Table A14 in Appendix A lists the system settings in numerical order. Included in the table are the item number, default setting, and page number reference of the setting description. To keep track of panel programming, it is recommended that you enter item number settings in Table A14 in Appendix A. Special Programming Settings Clear Panel Memory 0002 Default = NA It is recommended that you clear memory on all newly installed panels before programming. Clearing memory deletes setup values and resets all values to factory defaults. To Clear Panel Memory: 1. Enter program mode. 2. Enter the installer code. 3. Enter item number Press 99 and then #. Wait about a minute until touchpads return to their default displays. Since all programming information is contained in memory, clearing memory deletes all existing programming information except dealer values (if any). * Not investigated by UL. 1

18 Programming the Panel Reviewing (List) Settings Default = NA An easy way of listing all programming settings and their values is provided. You can list all settings, or settings starting at a selected item number. To List all Settings: 1. Once in program mode enter the item number (00000). 2. Press # to start listing settings from the beginning or enter the item number you wish to start at and press #. Touchpads will flash each of the item numbers and values (if not protected by dealer password). 3. Press * at any time to exit this menu. Displayed setting values may be viewed but not changed using this procedure. General Settings Areas Default = 0 (Off) Choose whether or not to treat partitions as areas. If treated as areas: q Zones, touchpads, schedules, programming options, etc., belong to areas instead of partitions. q Users may jump from one area to another area using an alphanumeric touchpad. q The word partition will be changed to area wherever it is spoken, displayed, or printed. To Turn Areas On/Off: Once the item number has been entered, enter 1 for on, or 0 for off. Press # to apply the new setting. Touchpad Return Time 1703 Default = 10 Seconds This setting allows you to select the length (in seconds) of inactivity (no menu activity) before a jumped touchpad returns to its assigned area. To Set Touchpad Return Time: 1. Once in program mode enter the item number. 2. Enter the desired length ( 60) and press #. Global Account Reporting Default = 0 (Off) The setting enables the panel to report events as a system. When set to on: q The panel will use the system account when reporting) events. The area number where the event occurred is also reported. q The panel will only perform one automatic phone test (not one for each partition/area). To turn Global Account Reporting On/Off: Once the item number has been entered, enter 1 for on, or 0 for off. Press # to apply the new setting. Partition/Area Enable xx068 Defaults = Partition/Area 1 1 (On), All Others 0 (Off) Choose whether or not to enable the partition/area. Partition/Area 1 is always enabled. To Enable/Disable a Partition/Area: Once the item number has been entered, enter 1 for on, or 0 for off. Press # to apply the new setting. Account Number 1 xx116 Account Number 2 xx117 Defaults = Enter an 8 digit account number. Each partition/area may have two account numbers. Account number 1 will use the primary phone number to report partition/area events, while account number 2 will use the secondary phone number to report partition/area events. Account Number Format: o for 0 enter 00 o for 6 enter 06 o for C enter 12 o for 1 enter 01 o for 7 enter 07 o for D enter 13 o for 2 enter 02 o for 8 enter 08 o for E enter 14 o for 3 enter 03 o for 9 enter 09 o for F enter 1 o for 4 enter 04 o for A enter 10 o for enter 0 o for B enter 11 To Enter an Account Number: 1. Once the desired item number has been entered the current account number will be displayed. 2. Enter the new account number using the list above. For example, if you wanted the account number to be 12346AB, at the keypad you would enter 01, 02, 03, 04, 0, 06, 10, Press # and the touchpad displays the new account number. Account numbers must equal 8 characters. If you enter less than 8 characters the panel will automatically replace the blank spaces with leading zeros (0). 16

19 Programming the Panel Partition/Area Text Default = None Use the following guidelines to assign each partition/area a name. q Use the item numbers that appear in Table B2 on page 8 for characters and words listed there. q If a desired word does not appear in Table B2, create it using the characters (custom text). q When using words from Table B2, spaces between them appear automatically. When using characters from Table B2 to create words, you must reserve an item number for a space after the word. q Each character or word uses up one item number. For example, a word from the list counts as one item number. A created word (such as BOY S) counts as six item numbers 4 letters, 1 apostrophe, and 1 space. q Only 8 item numbers are allowed for each partition/area name, so plan ahead before programming partition/area text. You may need to abbreviate words to avoid running out of item numbers. To Program Partition/Area Text: 1. Once in program mode enter The display shows ENTER PARTITION NUMBER OR PRESS * TO CANCEL. 2. Enter the desired partition number and press #. The display shows TEXT FOR PARTITION N IS CURRENT TEXT. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 3. Enter the numbers of the desired characters or words. If you make a mistake press * to start over. 4. Once all numbers have been entered, press # to accept. The display shows the new partition/area text. To Delete Partition/Area Text: 1. Once in program mode enter The display shows ENTER PARTITION NUMBER OR PRESS * TO CANCEL. 2. Enter the desired partition/area number and press #. The display shows TEXT FOR PARTITION N IS CURRENT TEXT. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 3. Enter 000 and press #. The display shows TEXT FOR PARTITION n IS NO TEXT. Alarm Settings LTime xx001 Default = 12:00 This is the time of day when the system will annunciate any existing trouble conditions. For Advent Commercial Burglary panels, trouble(s) are annunciated every 4 hours. If the LTIME is set at 12:00 pm then the system will announce trouble(s) at 12:00 pm, 4:00 pm, 8:00 pm, 12:00 am, 4:00 am, and 8:00 am. For Advent Home Navigator panels, trouble(s) are annuciated every 24 hours (at LTIME). To Set the LTIME Sound Time: Once the item number has been entered, enter the 4-digit time (00:00 23:9) in 24 hour format and press #. The Enable Daily Reporting of Partition/Area Trouble setting (xx108) must be set to on for this setting to work. Local Trouble Annunciation at LTime Default = 1 (On) Enables annunciation of all trouble conditions at LTime. xx108 To set the Local Trouble Annunciation at LTIME: Once the item number has been entered, enter 1 for on, or 0 for off. Press # to apply the new setting. Siren Sound Time xx002 Default = 16 Minutes (Commercial Burg) Default = 8 Minutes (Home Navigator) This is the number of minutes that the alarm siren is allowed to sound. The siren will silence when this value is reached. To Set Siren Sound Time: Once the item number has been entered, enter the number of minutes (01 30) you wish the siren to sound and press #. Exterior Siren Sounds Instantly xx113 Default = 0 (Off) This setting allows you to set the delay (in seconds) before an exterior siren sounds during and alarm. This includes all high level alarms, except for auxiliary alarms, which don t sound exterior sirens. If set to on, exterior sirens sound instantly. If set to off, exterior sirens sound after a 1-second delay. Turning Exterior Siren Delay On/Off: Once the item number has been entered, enter 1 for on (1-second delay), or 0 for off (no delay). Press # to apply the new setting. Zone Tamper Alarm Enable xx079 Default = 0 (Off) This setting determines whether a tamper alarm is generated for a zone that is not armed (applies to non-fire zones only). If on, a zone tamper alarm is generated when a zone tamper is detected in any arming level. If off, an alarm is only generated when the zone is in an active level. Turning Zone Tamper Report Enable On/Off: Once the item number has been entered, enter 1 for on (alarm in all levels), or 0 for off (alarm in active levels). Press # to apply the new setting. Fire Tamper Response xx083 Default = 0 (Off) This setting enables the panel to generate a tamper alarm (in addition to a trouble report) when tampering of a fire zone is detected. Setting Fire Tamper Response to On/Off: Once the item number has been entered, enter 1 for on (alarm is generated) or 0 for off (alarm not generated). Press # to apply the new setting. 17

20 Programming the Panel Keypad Tamper xx076 Default = 0 (Off) This setting enables keypad tamper. When on, the panel will generate a police alarm when it detects four or more incorrect access code entry attempts that do not include a valid access code. A tamper report is also sent to the central station. Turning the Keypad Tamper Setting On/Off: Once the item number has been entered, enter 1 for on (generate alarm and report) or 0 for off. Press # to apply the new setting. No Activity Internal xx009 Default = 0 (Not Active) This setting allows you to select the length of time (in hours) the panel will wait after not detecting any activity before initiating a no-activity pre-alarm. Once a no-activity pre-alarm is initiated the panel will wait until the time in the No Activity Report Delay setting (xx010) expires before generating an alarm. Setting the No Activity Internal Time: 1. Once the item number has been entered, enter the number of hours (1 24) you wish the panel to wait before initiating a noactivity pre-alarm, or 0 for not active. 2. Press # to apply the new setting. No Activity Report Delay xx010 Default = Minutes This setting allows you to select the length of time (in minutes) allowed after the No Activity Tripped setting (xx009) time has expired. If no activity is detected during this time the panel sends a report to the central station. If the user(s) generate activity within this delay period no report will be sent. Setting the No Activity Report Time: Once the item number has been entered, enter the number of minutes (1 10) you wish the panel to wait before sending a report. Press # to apply the new setting. If the No Activity Tripped After setting (xx009) is set to 0 (not active) this setting will have no affect. Generate Alarm for Suspicion Trips xx078 Default = 1 (On) This setting allows you to enable the panel to generate a suspicion trip alarm. If on, and suspicion zones are tripped, an alarm will be generated after the Suspicion Alarm Delay (xx01) expires. If off, the tripping of suspicion zones will not generate an alarm. To Turn Generate Alarm for Suspicion Trips On/Off: Once the item number has been entered, enter 1 for on or 0 for off. Press # to apply the new setting. Suspicion Alarm Delay xx01 Default = 0 Minutes Select the length of time in minutes in which an alarm can be avoided after a suspicion zone is tripped. This allows the user time to prevent a false alarm from being generated. Programming the Suspicion Alarm Delay: Once the item number has been entered, enter the number of minutes (1 1) you wish the panel to wait before going into alarm. Press # to apply the new setting. If the Generate Alarm Suspicion Trips setting (xx078) is set to off, this setting will have no effect. First Trip Local Second Trip Report xx080 Default = 0 (Off) If on, the first zone trip in a two trip zone type (18 or 77) causes a local police alarm. A second zone trip from a different zone, occurring within four minutes of the first zone trip, generates a report. Zones must reside in the same partition/area. If off, the first zone trip starts a timer and the second zone trip causes the alarm and report. To Turn This Setting On/Off: Once the item number has been entered, enter 1 for on or 0 for off. Press # to apply the new setting. X-10 and Non-X-10 Output Settings X-10 House Code 1 xx022 Default = Partition/Area Number The house code is a number from 1 to 16 (representing A P) used to communicate panel signals to line carrier devices such as X-10 Lamp, Appliance, and Universal Modules. You can have up to two house codes per partition/area. Enter the panel house code setting used for the first 16 X-10 line carrier devices. The system commands All Lights On/Off or All Units On/Off control only modules with House Code 1 (within respective partition/area). See Table B4 and B on page 90 for information on defaults. Entering House Code 1: Once the item number has been entered, enter the desired house code (1 16). Press # to apply the new setting. X-10 House Code 2 xx023 Default = Partition/Area Number + 8 Enter the panel house code setting used for the last 16 X-10 line carrier devices within respective partition/area. See Table B4 and B on page 91 for information on defaults. Entering House Code 2: Once the item number has been entered, enter the desired house code (1 16). Press # to apply the new setting. 18

21 Programming the Panel Reporting Settings Non X-10 Output 1 (menu output 33) xx049 Non X-10 Output 2 (menu output 34) xx00 Non X-10 Output 3 (menu output 3) xx01 Non X-10 Output 4 (menu output 36) xx02 Non X-10 Output (menu output 37) xx03 Non X-10 Output 6 (menu output 38) xx04 Non X-10 Output 7 (menu output 39) xx0 Non X-10 Output 8 (menu output 40) xx06 Default = 0 (None) There are 40 menu outputs per partition/area. The first 32 are X- 10 outputs, the last 8 are non X-10 outputs. All X-10 outputs (menu outputs 1-32) are automatically linked to X-10 devices. Non X-10 outputs (menu outputs 33-40) must be linked to a programmable output in order to control a light or device. All menu outputs must be programmed (learned) into the panel before they will function. See Programmable Output Settings on page 36 for more information. Linking Non X-10 Outputs: 1. Enter the item number for the desired non X-10 output. 2. Enter the desired programmable output number (1 100), then press # to confirm the selection. Report Partition/Area Events xx088 Default = 1 (On) If on, the panel will report partition/area events to the central station. Turning Partition/Area Event Reporting On/Off: Once the item number has been entered, enter 1 to turn partition/ area event reporting on or 0 turn reporting off. Press # to apply the new setting. Cancel Event Cancels Report xx089 Default = 1 (On) If on, the panel will cancel the sending of an alarm report (to central station) if the event is canceled before the alarm reporting delay (xx013, xx012, or xx014) expires. Turning Cancel Event Cancels Report On/Off: Once the item number has been entered, enter 1 to turn the setting on (canceled event cancels report) or 0 to turn it off. Press # to apply the new setting. Light Access Code Enable xx069 Default = 0 (Off) If on, users must enter a valid access code before controlling lights. If off, an access code is not required for light control. Turning Light Access Code On/Off: Once the item number has been entered, enter 1 for on (access code required), or 0 for off. Press # to apply the new setting. Print Partition/Area Events xx091 Default = 1 (On) If on, the panel will print partition/area events on a local printer. To Print Partition/Area Events: Once the item number has been entered, enter 1 (on) to enable printing of partition/area events or 0 (off) to disable printing of partition/area events. Press # to apply the new setting. Device Access Code Enable xx070 Default = 0 (Off) If on, users must enter a valid access code before controlling devices. If off, an access code is not required for device control. Turning Device Access Code On/Off: Once the item number has been entered, enter 1 for on (access code required) or 0 for off. Press # to apply the new setting. Latchkey Access Code Enable xx071 Default = 0 (Off) If on, users must enter a valid access code before accessing the Latchkey setting. If off, an access code is not required to access the Latchkey setting. For more information on Latchkey, please see the User s Manual. Turning Latchkey Access Code On/Off: Once the item number has been entered, enter 1 for on (access code required) or 0 for off. Press # to apply the new setting. Panic Report Delay xx012 Default = 0 Seconds This setting allows you to specify the length of time (in seconds) between the time a panic alarm condition is detected, and a panic report is sent to the central station. This allows users time to cancel the report of a false alarm if setting xx089 is on. Specifying the Panic Report Delay: Once the item number has been entered, enter the number of seconds (1 120) you wish the panel to wait before sending a panic report. Press # to apply the new setting. Alarm Report Delay xx013 Default = 0 Seconds This setting allows you to specify the length of time (in seconds) between the time a non-panic and non-fire alarm condition is detected, and a report is sent to the central station. This allows users time to cancel the report of a false alarm if setting xx089 is on. Specifying the Alarm Report Delay: Once the item number has been entered, enter the number of seconds (1 120) you wish the panel to wait before sending a report. Press # to apply the new setting. 19

22 Programming the Panel Arming Settings Fire Report Delay xx014 Default = 0 Minutes This setting allows you to specify the length of time (in minutes) between the time a fire alarm condition is detected, and a report is sent to the central station. This allows users time to cancel the report of a false alarm if setting xx089 is on. Specifying the Fire Report Delay: Once the item number has been entered, enter the number of minutes (0 1) you wish the panel to wait before sending a report. Press # to apply the new setting. Second Fire Alarm Ends Reporting Delay xx090 Default = 1 (On) If on, and a fire report delay is in progress, a second fire alarm condition will end the fire report delay (xx014) immediately sending a report to the central station. Programming Second Fire Alarm Ends Reporting Delay: Once the item number has been entered, enter 1 to turn the setting on (second alarm ends delay) or 0 to turn it off. Press # to apply the new setting. Enable Level 2 Arming xx02 Enable Level 3 Arming xx026 Enable Level 4 Arming xx027 Enable Level Arming xx028 Defaults = 1 (On) If on, the selected arming level will be enabled (level 1 is always enabled) in the selected partition/area. Users will then have access to this arming level. An arming level is the degree of security protection set at the panel. To Enable Arming Level: Once the item number has been entered, enter 1 to turn the setting on (level enabled) or 0 to turn it off. Press # to apply the new setting. Default Keyfob/Schedule Arming Level xx118 Default = 3 This setting allows you to select the arming level (2 ) the panel arms to when armed by a keyfob or schedule (auto arming). Specifying Keyfob/Schedule Arming Levels: Once the item number has been entered, enter the keyfob/scheduled arming level (2 ). Press # to apply the new setting. Second Intrusion Causes Report xx077 Default = 0 (Off) If on, the first trip of an intrusion zone causes a local police alarm. A second trip (different intrusion zone) within four minutes generates a report. If off, the first trip of an intrusion zone generates both an alarm and report. Setting Second Intrusion Causes Report: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Default Keyswitch Arming Level xx120 Default = 3 This setting allows you to select the arming level (2 ) the panel arms to when armed by a keyswitch. Specifying Keyswitch Arming Levels: Once the item number has been entered, enter the keyswitch arming level (2 ). Press # to apply the new setting. All Restoral Reports xx112 Default = 0 (Off) If on, restoral reports are generated for all reporting zone types (which require restoral). If off, the zone type definition dictates whether on not a restoral report is generated. Turning All Restoral Reports On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Local Closing Report Verification xx098 Default = 0 (Off) When on, the panel will locally verify that a closing report has been sent to the central station with an audible signal. In order for this setting to work, Exterior Siren Verification setting (xx097) must be set to on. To Turn Local Closing Report Verification On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Activity Fault Threshold 1 xx018 Activity Fault Threshold 2 xx019 Activity Fault Threshold 3 xx020 Defaults: Threshold 1 = 10, Threshold 2 = 30, Threshold = 0 This setting allows you to specify the number of disarms without any activity before zone activity trouble is generated. Specifying Activity Fault Thresholds: Once the item number has been entered, enter the number of disarms before zone activity trouble is generated (2 2). Press # to apply the new setting. Enable Scheduled Arming xx094 Default = 1 (On) This setting allows you to select whether or not to allow the system to arm/disarm according to a schedule. Turning Enable Scheduled Arming On/Off: Once the item number has been entered, enter 1 to enable scheduled arming or 0 to turn it off. Press # to apply the new setting. 20

23 Programming the Panel Scheduled Arming Period xx007 Default = 10 Minutes This is the amount of time between the start of arming notification and when the partition/area is armed by a schedule (auto arming). This notifies users that a scheduled arm is about to occur and allows time for users to vacate the premises. To Set the Scheduled Arming Period: Once the item number has been entered, enter the number of minutes (0 30) that will pass between notification and arming. Press # to apply the new setting. Exterior Siren Arming Verification xx097 Default = 0 (Off) If on, exterior sirens will produce arming verification sounds notifying users that the system was armed. In order for this setting to work, Local Closing Report Verification setting (xx098) must be set to on. To Turn Exterior Siren Arming Verification On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Scheduled Arming Extension xx008 Default = 30 Minutes This is the amount of time by which a scheduled arming period will be suspended during the arming notification period. For example, let s say the extension is entered when there is four minutes left in the delay. Once the extension has expired the system will start counting down the remaining four minutes. To Set the Scheduled Arming Extension: Once the item number has been entered, enter the number of minutes (1 120) users will be able to extend the notification period and press #. Auto Forced Arming xx092 Default = 1 (On) If on, any protesting zone(s) will be bypassed upon arming. If off, then the partition/area will not arm if any zone(s) are protesting. To Turn Auto Forced Arming On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Bypass Limit xx017 Default = 20/132 (all zones) Select the number of zones that may be bypassed at once. See Table B1 on page 80 for information on which zone types may be bypassed. To Program Bypass Limit Once the item number has been entered, enter the number of zones that may be bypassed at once (0 20). Press # to apply the new setting. Automatic Unbypass Enable xx096 Default = 0 (Off) If on, an indirectly bypassed zone will automatically be unbypassed once the door, window, etc., has been closed for 30 seconds. This setting only applies to delayed zones. To Turn Automatic Unbypass Enable On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Quick Arm xx093 Default = 1 (On) If on, anyone can arm the panel and increase arming levels without an access code. A valid access code is still required to decrease arming levels or disarm the system. Quick arm works as follows: o Level 3 to = no code o Level 1 to 2 = no code o Level 3 to 4 = code o Level 1 to 3 = no code o Level 4 to 3 = no code o Level 1 to 4 = no code o Level to 3 = code o Level 1 to = no code To Turn Quick Arming On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Swinger Bypass Enable xx09 Default = 1 (On) If on, a zone that exceeds the set swing count (xx021) during a single arming period will automatically be bypassed. Changing the arming level restores all automatically bypassed zones and resets the swing count. To Turn Swinger Bypass Enable On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Swing Count (Auto Bypass Trips xx021 Default = 3 Select the maximum number of report attempts that one zone can generate during a single arming period before the panel automatically bypasses that zone. All automatically bypassed zones, and the swing count, will reset if the system clock reaches midnight or an arming level change occurs. To Set the Swing Count: Once the item number has been entered, enter the desired swing count (1 8) and press # to apply the new setting. 21

24 Programming the Panel Entry Delay xx003 Default = 32 Seconds Enter the length of the standard entry delay (in seconds). This is the number of seconds the user has to disarm the system after tripping a standard delay zone. If the system isn t disarmed within this time period an alarm is generated. Setting the Entry Delay: Once the item number has been entered, enter the number of seconds (24 120) users will have to disarm the system. Press # to apply the new setting. Exit Delay xx004 Default = 32 Seconds Enter the length of the standard exit delay (in seconds). This is the number of seconds the user has to exit the premises through a standard delay door after arming the system. If the user trips a zone after this time period has expired, an alarm is generated. Setting the Exit Delay: Once the item number has been entered, enter the number of seconds (24 120) users will have to exit the premises after arming the system. Press # to apply the new setting. Extended Delay xx00 Default = 2 Minutes Enter the length of the extended delay. The extended delay time determines how much time (in minutes) the user has to enter or exit the premises through an extended delay door without causing an alarm. Setting the Extended Delay: Once the item number has been entered, enter the number of minutes (1 10) for the extended delay and press #. Exit Delay Reset xx102 Default = 0 (Off) If on, the system will allow a one-time reset of the standard exit delay. If a user leaves through a delay door and the door closes, they may re-enter through the door within the exit delay time period and the system will reset the exit delay. Cannot be used with Exit Delay Termination setting (xx101). To Turn Exit Delay Reset On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Fast Beep Duration xx006 Default = 10 Seconds Enter the length of time (in seconds) that fast beeps will sound during the last portion of the exit delay to signal the delay is ending. Setting the Fast Beep Duration: Once the item number has been entered, enter the number of seconds ( 1) fast beeps will sound before the end of the delay and press #. Exit Beeps only at end of Exit Delay xx100 Default = 1 (On) If on, only the fast beeps at the end of the exit delay will sound. If off, slow exit delay beeps will sound followed by the fast beeps at the end of the delay. To Turn Exit Delay Beeps On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Exit Delay Termination xx101 Default = 0 (Off) If on, the system will arm as soon as it detects a delay zone closing. Once a person leaves through an exit delay door and the door closes, the exit delay is terminated and the system is armed. Cannot be used with Exit Delay Reset setting (xx102). To Turn Exit Delay Termination On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Entry Delay Beeps xx103 Default = 0 (Off) If on, beeps only sound during the standard entry delay. If off, beeps sound during all segments of an entry delay including standard, extended, and twice extended. To Turn Entry Delay Beeps On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Zone Settings Chime Text xx110 Default = 0 (Off) If on, zone text will be announced over speakers and displayed on touchpads whenever a chime sounds (the sensor is open or closed). See Table B1 on page 79 for the zone types that chime. Only partition/area 1 has voice capabilities. To Turn Chime Text Setting On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. 22

25 Programming the Panel Close Chime xx111 Default = 0 (Off) If on, a chime will sound whenever a zone is restored. See Table B1 on page 79 for the zone types that chime. To Turn Close Chime Setting On/Off: Once the item number has been entered, enter 1 to turn the setting on or 0 to turn it off. Press # to apply the new setting. Zone Test Time Out xx011 Default = 30 Minutes Enter the length of time (in minutes) after which a zone test automatically times out (ends). Setting the Zone Test Time Out: Once the item number has been entered, enter the number of minutes ( 120) before a zone test ends and press #. Unlock Button Action (Default = 4) xx07 Lock Button Action (Default = 9) xx08 Lights Button Action (Default = 1) xx09 Star Button Action (Default = 12) xx060 Lights/Star Button Combination Action xx061 (Default = 3) Direct Arm Level 3 Action (Default = 6) xx063 Direct Arm Level 2 Action (Default = ) xx064 Lock/Star Button Combination Action xx06 (Default = 16) Disarm/Lights Button Combination Action xx066 (Default = 16) These settings allow you to specify how the system behaves when specific keychain touchpad button or button combinations are pressed. Special Action Assignments: q 0- not used q 1- not used q 2- not used q 3- auxiliary panic (only used for item no. xx061) q 4- arm to level 1 q - arm to level 2 q 6- arm to level 3 q 7- arm to special level 4 q 8- arm to special level q 9- arm to closed level q 10- arm to closed level with no delay q 11- arm to closed level with Latchkey q 12- increment arming level from 0 to 1, 1 to 2, or 2 to 3 only q 13- turn all* lights on q 14- turn all* lights off q 1- toggle all* lights q 16- do nothing * all lights having the first (of two) house codes in the partition. Specifying Keychain Touchpad Button Action: 1. Once the desired item number has been entered, enter the special action assignment number (3 16) from the above list. 2. Press # to apply the new setting. Auxiliary Medical Panic Keys xx086 Default = 1 (On) Choose whether or not to enable the Auxiliary panic buttons on touchpads. If enabled, when a user presses and holds the Auxiliary panic buttons or presses them twice, an auxiliary or medical alarm is generated. See Auxiliary/Medical Assignment setting (xx084). To Turn This Setting On/Off: Once the item number has been entered, enter 1 to turn the setting on (enabled) or 0 to turn it off. Press # to apply the new setting. Enable Police Panic Keys xx08 Default = 1 (On) Choose whether or not to enable the Police panic buttons on touchpads. If enabled, when a user presses and holds the police panic buttons or presses them twice, a police alarm is generated. To Turn This Setting On/Off: Once the item number has been entered, enter 1 to turn the setting on (enabled) or 0 to turn it off. Press # to apply the new setting. Enable Fire Panic Keys xx087 Default = 1 (On) Choose whether or not to enable the Fire panic buttons on touchpads. If enabled, when a user presses and holds the fire panic buttons or presses them twice, a fire alarm is generated. To Turn This Setting On/Off: Once the item number has been entered, enter 1 to turn the setting on (enabled) or 0 to turn it off. Press # to apply the new setting. Auxiliary/Medical Assignment xx084 Default = 1 (On Auxiliary Alarm) Choose whether the Auxiliary/Medical panic buttons are used to produce an auxiliary (on) or medical (off) alarm. In order for an auxiliary or medical alarm to be produced by the pressing of the panic buttons, they must be enabled. See the Auxiliary Medical Panic Enable setting xx086. Selecting the Alarm Type: Once the item number has been entered, enter 1 to turn the setting on (auxiliary) or 0 to turn it off (medical). Press # to apply the new setting. Codes The settings below cover only installer programming codes. For information on user access code programming, please refer to the User s Guide. 23

26 Programming the Panel Dealer Access Code Default = None Enter a six-digit Dealer Access code. This code is used to access special programming menus such as setting reporting phone numbers or account numbers when the panel is in program mode. If this code is not set, these programming menus require no special code to access. Setting the Dealer Access Code: 1. Once the item number has been entered, enter any six-digits (0 9) then press #. 2. When prompted, enter the six-digit code again (for verification), and press #. 3. The touchpad will display NEW CODE OK. Changing/Deleting the Dealer Access Code: 1. Once the item number has been entered, enter the six-digit dealer code. 2. Wait until the touchpad displays ENTER NEW CODE then q enter a new six-digit dealer code or, q enter 0 + # to delete the dealer access code (no code). 3. Enter the new code again. 4. The touchpad will display NEW CODE OK. If a Dealer Access Code has been set clearing the panel s memory will not clear the Dealer Access Code, Reporting Phone Numbers, or Account Numbers. If the Dealer Access Code is set, the forgotten, the only way to clear it is to return the panel to the factory. Downloader Access Code Default = 1234 Enter a five-digit access code to be used in conjunction with downloader programming. This code must match (or be left at default) the downloader access code programmed in downloader in order for the two to communicate. Changing the Downloader Access Code: 1. Enter the item number. If a Dealer Access Code has been programmed, you will be prompted to enter it. 2. Once the Dealer Access Code has been entered (if applicable) the touchpad will display the current Downloader Access Code. 3. Enter any five-digits (0 9) for the new Downloader Access code, then press #. Access Code Length 0013 Default = 4 Select the required length of all installer, primary, and user access codes. If the access code length is changed, then all access codes will automatically be updated to the correct length. Access codes that contained less digits than the new length will be given leading zeros (1234 = ). Access codes that contained more digits than the new length will be have the first digit(s) removed (98764 = 764). Changing the Access Code Length: 1. Enter the item number. The current code length will be displayed. 2. Enter the new code length (4 6) and press #. Phone Settings Enable Phone Line 1 DTMF Dialing Enable Phone Line 2 DTMF Dialing 1709 Defaults = 1 (On) Select whether or not you want to enable the phone line for DTMF (touch-tone) dialing. If off, the panel will dial using pulse format. To Set Dialing format: Once the item number has been entered, enter 1 to turn this setting on (DTMF dialing) or 0 to turn it off (pulse dialing). Press # to apply the new setting. Phone Line 1 Dialing Prefix 1710 Phone Line 2 Dialing Prefix Defaults = None Enter up to a six-digit phone line dialing prefix. Use this setting to access an outside line, disable call waiting, etc. Line Dial Prefix Format q Enter for numbers 0-9 q Enter 10 for * (star) q Enter 11 for # (pound) q Enter 12 for D (1 second delay) q Enter 13 for W (wait for dial tone) Setting a Line Dialing Prefix: 1. Once the desired item number has been entered the current line dial prefix will be displayed. 2. Enter up to a six-digit phone line dialing prefix using the format above and press #. Deleting a Line Dialing Prefix: 1. Once the desired item number has been entered the current line dial prefix will be displayed. 2. Enter 0 + #. The touchpad will display NO DATA. 24

27 Programming the Panel Buddy Dial Attempts Default = Set the number of dialing attempts (to central station) before a buddy transmission is generated. Setting the Number of Buddy Dial Attempts: Once the item number has been entered, enter the number of buddy dial attempts (0-11)* and press #. * 0 = immediate transmit request, 11 = no transmit request. No Phone Line Default = 0 (Off) Turn this setting on if there is no phone line connected to the panel. When on, the panel will not check for phone line failure. Turning No Phone Line Setting On/Off: Once the item number has been entered, enter 1 to turn this setting on (no phone line) or 0 to turn it off (phone line). Press # to apply the new setting. System Account Number System Account Number Defaults = Enter an 8-digit system account number which will identify the panel to the central station when reporting system events. System Account Number 1 is reported on reporting phone 1 and its backup. System account number 2 is reported on reporting phone 2 and its backup. Account Number Format: o for 0 enter 00 o for 6 enter 06 o for C enter 12 o for 1 enter 01 o for 7 enter 07 o for D enter 13 o for 2 enter 02 o for 8 enter 08 o for E enter 14 o for 3 enter 03 o for 9 enter 09 o for F enter 1 o for 4 enter 04 o for A enter 10 o for enter 0 o for B enter 11 To Enter a System Account Number 1. Once the desired item number has been entered the current system account number will be displayed. If a Dealer Access Code has been programmed, you will be prompted to enter it. 2. Enter the new system account number using the list above. For example, if you wanted the system account number to be 12346AB, at the keypad you would enter 01, 02, 03, 04, 0, 06, 10, Press # and the touchpad displays the new system account number. System account numbers must equal 8 characters. If you enter less than 8 characters the panel will automatically replace the blank spaces with leading zeros (0). Pager ID 1708 Default = The Pager ID identifies the panel to pager-holders. Select the ID to be sent with pager reports. Setting System Pager ID: Once the item number has been entered, enter the -digit Pager ID ( ) to be sent with pager reports and press #. Interval Between Automatic Phone Test17034 Default = 1 (Commercial), 7 (Home Navigator) Select the number of days between automatic phone test reports to all enabled central station phone numbers. Entering 0 will disable automatic phone test. To Set Automatic Phone Test Interval: Once the item number has been entered (17-034), enter THE NUM- BER OF DAYS (0-2). Press # to apply the new setting. Specific Phone Number Settings Specific phone number settings allow you to program central monitoring station, downloader, and pager phone numbers. If a Dealer Access Code has been programmed, you will be prompted to enter it when setting/changing specific phone settings. q Phone numbers are central monitoring station reporting phone numbers and function as follows: 19 = phone 1 20 = phone 1 backup 21 = phone 2 22 = phone 2 backup q Phone numbers are downloader phone numbers and function as follows: 23 = phone 3 24 = phone 3 backup q Phone numbers 2 40 are reporting pager phone numbers 1 through 16. Central Monitoring Station and Downloader Phone Number Settings Phone Number Enable yy001 Default = 0 (Off) Select whether or not to enable the phone number. If on, the panel will use the number when reporting or downloading. If off, the number will be skipped. To Turn Reporting Phone Number On/Off: Once the item number has been entered ( ), enter 1 to turn this setting on (call), or 0 to turn it off (no call). Press # to apply the new setting. 2

28 Programming the Panel Phone Number yy002 Default = None Enter up to a 24-digit phone number for reporting or downloading. Phone Number Format q Enter for numbers 0-9 q Enter 10 for * (star) q Enter 11 for # (pound) q Enter 12 for D (1 second delay) q Enter 13 for W (wait for dial tone) To Enter a Phone Number: 1. Enter the desired item number (ex ). 2. Enter the phone number using the list above. For example, if you wanted the phone number to be , at the keypad you would enter 01, 02, 03, 0, 0, 0, 01, 02, 01, Press # and the touchpad displays the new phone number. In order for the phone number to be used for reporting events or downloading, it must be enabled. See the Phone Number Enable setting (yy001). To Delete a Phone Number: 1. Enter the desired item number. 2. Enter 0 + #. The touchpad will display NO DATA. Number of Attempts yy003 Default = Set the number of times (attempts) the panel will dial (and report) to the reporting or downloader phone number for phones 1 and its backup, for phones 2 and its backup. Setting the Number of Dial Attempts: Once the item number has been entered, enter the number of dial attempts ( 10) and press #. Communication Format yy004 Default = 0 (Contact ID) Select the type of communication format the panel will use when reporting events to the central station. Currently only Contact ID format is supported. Report Panic Special yy00 Default = 0 (Off) Choose how the panel formats touchpad panic alarm reports to the central station. When on, touchpad panic alarms report using the following special 3-digit codes: q Fire Panic 99 q Police Panic 98 q Auxiliary Panic 97 q Medical Panic 96 When off, panics will report as 00 plus the bus device number. For example, a keypad with bus device number 03 would report as 03. Turning Report Panic Special On/Off: Once the item number has been entered, enter 1 to turn this setting on (report panic special), or 0 to turn it off (not special). Press # to apply the new setting. Pager Phone Number Settings Pager Phone Number Enable zz001 Default = 0 (Off) Select whether or not to enable the pager phone number. If on, number will report events to the pager. If off, the number will be skipped when the panel is reporting to pagers. To Turn Reporting Pager Phone Number On/Off: 1. Once the item number has been entered ( ), enter 1 to turn this setting on (page), or 0 to turn it off (no page). 2. Press # to apply the new setting. Pager Phone Number Default = None Enter up to a 24-digit phone number for pager reporting. Pager Phone Number Format q Enter for numbers 0-9 q Enter 10 for * (star) q Enter 11 for # (pound) q Enter 12 for D (1 second delay) q Enter 13 for W (wait for dial tone) To Enter a Pager Phone Number: zz Enter the desired item number (ex. 2002). 2. Enter the phone number using the list above. For example, if you wanted the pager phone number to be , at the keypad you would enter 01, 02, 03, 0, 0, 0, 01, 02, 01, Press # and the touchpad displays the new pager phone number. In order for the panel to report events to the pager the pager phone number must be enabled. See Pager Phone Number Enable setting (zz001). To Delete a Pager Phone Number: 1. Enter the desired item number. 2. Enter 0 + #. The touchpad will display NO DATA. 26

29 Programming the Panel Number of Attempts zz003 Default = 3 Set the number of times (attempts) the panel will try to dial the pager phone number. Setting the Number of Dial Attempts: Once the item number has been entered, enter the number of dial attempts (3 10) and press #. Communication Format zz004 Default = 1 (TAP at 1200 bps PSK) Select the type of communication format the panel will use when reporting events to pagers. Consult your paging service provider for help in setting this option. Communication Formats: q Enter 0 for TAP at 300 bps (FSK). q Enter 1 for TAP at 1200 bps (PSK). Setting the Communication Format 1. Once the item number has been entered, use the choices above to select a communication format. 2. Press # to apply the new setting. Partition/Area 1 Reports zz007 (Defaults = 0, Phone 2 = 1) Partition/Area 2 Reports zz008 (Defaults = 0, Phone 26 = 1) Partition/Area 3 Reports zz009 (Defaults = 0, Phone 27 = 1) Partition/Area 4 Reports zz010 (Defaults = 0, Phone 28 = 1) Partition/Area Reports zz011* (Defaults = 0, Phone 29 = 1) Partition/Area 6 Reports zz012* (Defaults = 0, Phone 30 = 1) Partition/Area 7 Reports zz013* (Defaults = 0, Phone 31 = 1) Partition/Area 8 Reports zz014* (Defaults = 0, Phone 32 = 1) Select whether or not you want partition/area events to report to pager(s). To turn Partition/Area Report On/Off: 1. Once the item number has been entered, enter 1 to turn this setting on (report), or 0 to turn it off (don t report). 2. Press # to apply the new setting. * This option setting is available on 8 partition panel types only ( and ). Communication Character Format zz00 Default = 1 (7/E/1) Select the character format the panel will use when reporting to pagers. Consult your paging service provider for help in setting this option. Character Formats q Enter 0 for 8/N/1. q Enter 1 for 7/E/1. Setting the Character Format 1. Once the item number has been entered, press 0 for 8/N/1 character format (off), or 1 for 7/N/1 character format (on). 2. Press # to apply the setting. Pager System Reports zz006 Default = 0 (Off) Select whether or not you want system events reported to pager. To Turn System Pager Report On/Off: Once the item number has been entered, enter 1 to turn this setting on (report), or 0 to turn it off (don t report). Press # to apply the new setting. Pager PIN zz01 Default = None Enter up to a 1-digit pager PIN. Consult your paging service provider for help in setting this option. To Enter a Pager PIN: 1. Enter the desired item number (ex. 201). 2. Enter up to a 1-digit (0 9) pager PIN. 3. Press # and the touchpad displays the pager PIN. Pager Message Length zz016 Default = 120 Characters Set the maximum character length for pager messages. Consult your paging service provider for help in setting this option. Setting Maximum Pager Message Length: Once the item number has been entered, enter the maximum pager length (0 2) and press #. Advanced Phone Settings &$87,21 Only qualified persons should make changes to advanced phone settings. Maximum Ring Cycle Time Default = 67 Milliseconds Specify (in milliseconds) the maximum cycle time for the ring signal. Setting the Maximum Ring Cycle Time: 1. Once the item number has been entered, specify the maximum ring cycle time (0 2). 2. Press # to apply the new setting. 27

30 Programming the Panel Minimum Tone Duration Default = 3 (30 ms) Specify the minimum duration of a valid DTMF (touch-tone) tone in 10 millisecond increments (1 100 x 10 ms). This is the minimum amount of time that a phone number button must be pressed in order to be valid. Setting the Minimum Tone Duration: 1. Once the item number has been entered, specify the minimum tone duration (1 100). 2. Press # to apply the new setting. Minimum Duration Between Tones Default = (0 ms) Specify the minimum duration of pause between DTMF (touchtone) tones in 10 millisecond increments (1 100 x 10 ms). This is the minimum amount of time required between two phone number buttons being pressed. Setting the Minimum Duration Between Tones: 1. Once the item number has been entered, specify the minimum duration between tones (1 100). 2. Press # to apply the new setting. Minimum Valid Ring Cycles 1704 Default = 2 Cycles Specify the minimum number of cycles in a valid ring. Setting the Minimum Valid Ring Cycles: 1. Once the item number has been entered, specify the minimum number of cycles (0 2). 2. Press # to apply the new setting. Valid Ring Bursts 170 Default = 1 Burst Specify the number of ring bursts in a valid ring. Setting the Number of Ring Bursts: 1. Once the item number has been entered, specify the number of ring bursts (1 ). 2. Press # to apply the new setting. Valid Ring at Beginning or End of Ring Burst Default = 0 (Off) Selects if a ring is considered valid at the beginning of the ring burst or at the end of the ring burst. Setting Valid Ring at Beginning or End of Cycle: Once the item number has been entered, enter 1 or 0. Press # to apply the new setting. Maximum Ring Burst Duration Default = 20 (200 ms) Specify the maximum duration of a valid ring burst in 10 ms increments (3 300 x 10 ms). Setting the Maximum Ring Burst Duration: 1. Once the item number has been entered, specify the maximum ring burst duration (3 300). 2. Press # to apply the new setting. Minimum Ring Burst Duration Default = 40 (400 ms) Specify the minimum duration of a valid ring burst in 10 ms increments (3 300 x 10 ms). Setting the Minimum Ring Burst Duration: 1. Once the item number has been entered, specify the minimum ring burst duration (3 300). 2. Press # to apply the new setting. Maximum Duration Between Ring Bursts Default = 0 Specify the maximum duration between valid ring bursts in 10 millisecond increments (0 300 x 10 ms). Setting the Maximum Duration Between Ring Bursts: 1. Once the item number has been entered, specify the maximum duration between ring bursts (0 300). 2. Press # to apply the new setting. Minimum Duration Between Ring Bursts Default = 0 Specify the minimum duration between valid ring bursts in 10 millisecond increments (0 300 x 10 ms). Setting the Minimum Duration Between Ring Bursts: 1. Once the item number has been entered, specify the minimum duration between ring bursts (0 300). 2. Press # to apply the new setting. Maximum Time Between Rings Default = 40 (400 ms) Specify the maximum amount of time allowed between valid rings in 10 millisecond increments ( x 10 ms). Setting the Maximum Time Between Rings: 1. Once the item number has been entered, specify the maximum time between rings ( ). 2. Press # to apply the new setting. 28

31 Programming the Panel Minimum Time Between Rings Default = 200 (2000 ms) Specify the minimum amount of time allowed between valid rings in 10 millisecond increments ( x 10 ms). Setting the Minimum Time Between Rings: 1. Once the item number has been entered, specify the minimum time between rings ( ). 2. Press # to apply the new setting. Phone Access Settings Local Phone Settings Local phone settings allow you to choose how phones located on the same premises as the panel interact with the system. Enable Local Phone Access in Partition/Area Default = 0 (Off - Commercial Burg) Default = 1 (On - Home Navigator) This setting allows you to enable local phone control in partition/ area 1. If on, partition/area 1 may be controlled by local on premises phones. To Turn Local Phone Access in Partition/Area 1 On/Off: Once the item number has been entered, enter 1 to turn this setting on, or 0 to turn it off. Press # to apply the new setting. Local Phone Control Sequence 1706 Default = #* Enter up to a 4-digit DTMF (touch-tone) sequence for local phone control. This is the sequence of numbers the user will have to enter when accessing the panel locally (on-site). Partition/area 1 only. Format: q Enter for numbers 0-9. q Enter 10 for * (star). q Enter 11 for # (pound). To Enter Local Phone Control Sequence: 1. Enter the item number. 2. Enter the sequence using the format above. For example, if you wanted the sequence to be 12#*, at the keypad you would enter 01, 02, 11, Press # and the touchpad displays the new sequence. To Delete the Local Phone Control Sequence: 1. Enter the item number. 2. Enter 0 + #. The touchpad will display NO DATA. Phone Device Override Sequence 1707 Default = **## Enter up to a 4-digit DTMF (touch-tone) sequence for phone device override. This sequence will instruct the panel to seize the line from the local phone and initiate a remote connection. Users will be able to enter this sequence and bypass any phone devices (answering machines, fax machines, etc.) when calling from a remote phone. Partition/area 1 only. Format: q Enter for numbers 0-9. q Enter 10 for * (star). q Enter 11 for # (pound). To Enter Phone Device Override Sequence: 1. Enter the item number. 2. Enter the sequence using the format above. For example, if you wanted the sequence to be 12#*, at the keypad you would enter 01, 02, 11, Press # and the touchpad displays the new sequence. To Delete Phone Device Override Sequence: 1. Enter the item number. 2. Enter 0 + #. The touchpad will display NO DATA. Time Between Phone Panic Keystrokes Default = 2 Seconds Specify the maximum time allowed (in seconds) between keystrokes in a phone panic sequence. If this delay is exceeded, a panic alarm will not be activated. Partition/area 1 only. Setting the Time Between Phone Panic Keystrokes: 1. Once the item number has been entered, enter the maximum delay (1 ). 2. Press # to apply the new setting. Local Phone Connect Time Default = Seconds Specify the maximum time allowed (in seconds) between local phone off-hook and DTMF seize sequence for local phone control. If the maximum time is exceeded, remote phone control will be put on hold. Partition/area 1 only. Setting the Local Phone Connect Time: 1. Once the item number has been entered, enter the maximum allowable connect time (0 2 [0 = no max time]). 2. Press # to apply the new setting. Local Phone Answer Time Default = 8 Seconds Specify the maximum time (in seconds) between a ring signal and local phone off-hook signal to be considered answer of call. Partition/area 1 only. Setting the Local Phone Answer Time: 1. Once the item number has been entered, enter the answer time (0 2). 2. Press # to apply the new setting. 29

32 Programming the Panel On Hook Hang Up Time Default = 4 Seconds Select the amount of time (in seconds) a local telephone must be on-hook before hanging up. Partition/area 1 only. Setting the On Hook Hang Up Time: 1. Once the item number has been entered, enter the hang up time (2 10). 2. Press # to apply the new setting. Phone Police Panic Enable Phone Aux/Med Panic Enable Phone Fire Panic Enable Defaults = 0 (Off) Select whether or not you want to enable the selected phone panic sequence. If on, users will be able to activate the specific panic alarm using a local phone (88888 for police, for auxiliary/ medical, and for fire). Partition/area 1 only. To Turn Phone Panic On/Off: Once the desired item number has been entered, enter 1 to turn this setting on, or 0 to turn it off. Press # to apply the new setting. Remote Phone Settings Remote phone settings allow you to choose how phones located off premises (different line) interact with the panel. Enable Remote Phone Access Default = 1 (On) Turning this setting to off will prevent the panel from receiving future downloader calls. This setting allows you to enable remote phone access. If on, the panel may be controlled using remote off-site phones. Partition/ area 1 only. For residential use only. To Turn Remote Phone Access On/Off: 1. Once the item number has been entered, enter 1 to turn this setting on (enabled), or 0 to turn it off. 2. Press # to apply the new setting. Enable Remote Phone Ring Count Default = 1 (On) This setting allows you to tell the panel to count remote phone rings so that it will pick up after a certain number of rings. This setting only works if Remote Phone Access setting (above) is set to on. Partition/area 1 only. For residential use only. To Turn Remote Phone Ring Count On/Off: 1. Once the item number has been entered, enter 1 to turn this setting on, or 0 to turn it off. 2. Press # to apply the new setting. Answer Phone after XX Rings 1702 Default = 12 Rings Specify the number of rings after which the panel will answer an incoming phone call. The Remote Phone Ring Count (17087) setting must be set to on for this setting to work. Partition/area 1 only. For residential use only. To Set the Number of Rings: 1. Once the item number has been entered, specify the maximum number of rings (1 12). 2. Press # to apply the new setting. Enable Toll Saver Default = 1 (On) Choose whether or not to enable the panel to answer a remote phone up to 4-rings earlier than normal if an alarm condition or system trouble has occurred. Normal is considered the value in Answer Phone After XX Rings setting (1702). The Remote Phone Ring Count setting (17087) must be set to on for this setting to take effect. Partition/area 1 only. For residential use only. To Turn Toll Saver On/Off: 1. Once the item number has been entered, enter 1 to turn this setting on, or 0 to turn it off. 2. Press # to apply the new setting. Enable Remote Phone Ring-Pause-Ring Default = 1 (On) This setting allows you to program the panel to answer remote phone ring-pause-rings. When on, a user can call the panel once, hang up, and call again. The panel will then answer the phone. Use this setting if an answering machine shares a phone line with the panel. Partition/area 1 only. The user must not exceed the number of rings in the Cancel Ring Pause Ring after XX Rings setting (1703) when calling the panel. Additionally, the user must call the panel again between the times programmed in settings 1702 and For residential use only. To Turn Remote Phone Ring-Pause-Ring On/Off: Once the item number has been entered, enter 1 to turn this setting on, or 0 to turn it off. Press # to apply the new setting. Min Time Between Ring-Pause-Ring Calls 1702 Default = 10 Seconds Specify the minimum time (in seconds) between ring-pause-ring calls. This is the minimum amount of time that must elapse before the second call in a ring-pause-ring attempt. Partition/area 1 only. Setting the Minimum Time Between Ring-Pause-Ring Calls: 1. Once the item number has been entered, specify the minimum time (6 20). 2. Press # to apply the new setting. 30

33 Programming the Panel Max Time Between Ring-Pause-Ring Calls Default = 30 Seconds Specify the maximum time (in seconds) between ring-pause-ring calls. This is the maximum amount of time that may elapse before the second call in a ring-pause-ring attempt. If this time is exceeded, the current ring-pause-ring attempt will be canceled. Partition/area 1 only. Setting the Maximum Time Between Ring-Pause-Ring Calls: 1. Once the item number has been entered, specify the maximum time (7 60). 2. Press # to apply the new setting. Cancel Ring Pause Ring After XX Rings 1703 Default = 3 Rings Specify the number or rings at which ring-pause-ring is aborted. For example, if this setting is set at 3, then (during the first call) at 3 rings, ring-pause-ring will be aborted. Partition/area 1 only. Setting Cancel Ring Pause Ring After XX Rings: 1. Once the item number has been entered, specify the maximum number of rings (2 10). 2. Press # to apply the new setting. Enable Remote Phone Override Default = 1 (On) If on, users may cut off a local phone call or answering machine to access the panel from a remote phone. Partition/area 1 only. For residential use only. To Turn Remote Phone Override On/Off: 1. Once the item number has been entered, enter 1 to turn this setting on, or 0 to turn it off. 2. Press # to apply the new setting. Allow Remote Phone Zone Test Default = 1 (On) If on, users may perform zone tests from remote phones. Partition/area 1 only. To Turn Remote Phone Zone Test On/Off: 1. Once the item number has been entered, enter 1 to turn this setting on, or 0 to turn it off. 2. Press # to apply the new setting. Zone Settings Use zone settings to add, delete, test, and modify zones. It is recommended that no more than 132 wireless sensors be used in any individual Advent system. If 2 or more Advent systems are in close proximity to each other, the total number of wireless sensors for all systems must not exceed 132. Add (Learn) Zones Default = NA Use this item number to add (learn) hardwire zones and wireless devices into panel memory. To Learn Zones Into Panel Memory: 1. Once in program mode enter item number The display shows ENTER PARTITION/AREA NUMBER OR PRESS * TO CANCEL. 2. Enter the desired one-digit partition/area number (1 8) and press #. The display shows ENTER ZONE TYPE OR PRESS * TO CANCEL. If the partition/area is not enabled, the display will show PARTITION/AREA nn INVALID. See item number xx068 to enable partition/area(s). 3. Enter the two-digit zone type number (00 96) and press #. Refer to Table B1 in Appendix B on page 80 for zone type descriptions. If zone type 84 (Enhanced Buddy) is selected the zone number prompt is skipped and buddy learn mode is automatically entered. While in this mode, the panel sends and receives buddy learn messages and adds (learns) all buddies that it detects (up to 4) when the * or # button is pressed in this mode, the panel automatically proceeds to buddy test mode where a buddy test message is sent and acknowledged by all buddy panels. At the end of this test, the panel indicates the IDs of the buddy panels, and the received signal strength from each. 4. The display shows LEARN ZONE nn ENTER NEW ZONE NUMBER OR PRESS # TO ACCEPT, where nn is the next available zone number. If desired, enter a different zone number. Press #.. When the display shows TRIP ZONE n, use the guidelines below and on this page to trip the zone you are adding which learns it into panel memory. 6. The display shows ZONE nn TYPE nn PARTITION/AREA n OK. 7. To add another zone to the same zone type and partition/area, go to step. To add zones to another zone type (same partition/area) press # and go back to step 3. To add zones to another zone type and partition/area press * and repeat the above procedure (exits to programming). Make sure wireless touchpads that may be removed from the premises such as portable and keychain touchpads are assigned to an unsupervised zone type such as 87. Assign permanently mounted wireless touchpads to supervised zone type 86. Tripping Hardwire Zones q Hardwire Zones Start with the zone in its normal state, then trip the zone into its alarm state. A normally closed door, for example, should be closed when you begin the Add Zones process. Trip the zone by opening the door. q On hardwired zones containing multiple sensors, only one needs to be tripped for the panel to learn the zone. q The alarm state is either open or closed, depending on the normal condition of the sensor. Multiple normally closed switches are wired in series and tripped open. Multiple normally open switches are wired in parallel and tripped closed. 31

34 Programming the Panel Tripping Learn Mode Wireless Sensors * * Refer to the specific sensor/touchpad Installation Instructions for more details on tripping sensors/touchpads. ** When using an external contact with this sensor, the contact must be in the alarm state while tripping the sensor to properly learn it into memory. To trip a wireless sensor with an external hardwired contact connected to its screw terminals, check that the external contact is in its alarm state, then activate the sensor tamper. For high-security installations, always remove both internal reed switches when connecting an external contact to the wireless sensor terminals. Only the normally closed configuration can be used in UL- listed installations. Do not attempt to use the built-in magnetic reed switch and an external contact on the same wireless sensor. On hardwired sensors connected to the external contacts of a wireless transmitter, the alarm state is either open or closed, depending on the normal condition of the sensor. Multiple normally closed switches are wired in series and tripped while the loop is open. Multiple normally open switches are wired in parallel and tripped while the loop is closed. q Door/Window Sensors with External Contacts Place the external contact in the alarm condition, then activate the sensor tamper switch (remove cover). q Fire Pull Station Actuate the sensor. Open the sensor cover located inside the fire pull station. q Glass Guard Open sensor cover. q Portable Emergency Buttons Press and hold emergency button(s). q PIR Motion Open PIR case. q Rate-of Rise-Heat Open sensor cover and press learn switch on circuit board. q Recessed Door/Window Open sensor cover and remove transmitter circuit board. q Micro Recessed Door/Window Short contacts in small screwdriver slot. q Shock Sensor ** Open sensor cover. q Slim Line Door/Window Remove sensor from mounting base. q ITI Sound Open sound sensor cover after spring is installed. q Smoke (System Sensor 2100RF) Remove base. q Smoke (System Sensor 2100ARFT) Remove base. q Smoke (Sentrol 60) Remove base. q Smoke (Sentrol 70) Remove base. q Pressure Switch Sensor Hold a magnet next to the sensor cover where indicated (does not require cover removal). q 2 and 4 Button Keychain Touchpads Simultaneously press Lock and Unlock buttons until the touchpad LED flashes (added [learned] in a sensor zone type). q Handheld Press Bypass button. q HiTech Wall-Mount Press Bypass button. q HiTech Handheld Press Bypass button. Delete Zones Default = NA Use this item number to delete zones from panel memory. You must delete zones one at a time. Deleting zones does not delete the zone text associated with the deleted zone number. To delete zone text use item number To Delete Zones from panel memory: 1. Once in program mode enter The display shows ENTER ZONE NUMBER OR PRESS * TO CANCEL. 2. Enter the 3-digit zone number you wish to delete and press #. 3. The display shows ZONE nn DELETED. 4. To delete another zone, repeat the above procedure. Zone Text Default = None Use the following guidelines to name zones. q Use the item numbers that appear in Table B2 on page 8 for characters and words listed there. q If a desired word does not appear in Table B2, create it using the characters (custom text). q When using words from Table B2, spaces between them appear automatically. When using characters from Table B2 to create words, you must reserve an item number for a space after the word. q Each character or word uses up one item number. For example, a word from the list counts as one item number. A created word (such as BOY S) counts as six item numbers 4 letters, 1 apostrophe, and 1 space. q Only 8 item numbers are allowed for each zone name, so plan ahead before programming zone text. You may need to abbreviate words to avoid running out of item numbers. To Program Zone Text: 1. Once in program mode enter The display shows ENTER ZONE NUMBER OR PRESS * TO CANCEL. 2. Enter the desired zone number and press #. The display shows TEXT FOR ZONE n IS CURRENT ZONE TEXT. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 3. Enter the numbers of the desired characters or words. If you make a mistake press * to start over. 4. Press # to accept. The display shows the new zone text. To Delete Zone Text: 1. Once in program mode enter The display shows ENTER ZONE NUMBER OR PRESS * TO CANCEL. 2. Enter the desired zone number and press #. The display shows TEXT FOR ZONE n IS CURRENT ZONE TEXT. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 3. Enter 000 and press #. The display shows TEXT FOR ZONE n IS NO TEXT. 32

35 Programming the Panel List Zones Default = NA Use this item number to list information about existing zones. The system will list the zone number, any zone text, zone type number, and the partition/area number. To List Zones: Once in program mode enter The display will show ZONE nn, ANY ZONE TEXT, TYPE nn, PARTITION/AREA n. The panel will scroll through and display information about each zone. To skip forward press #. To exit press *. Once the panel lists all the zones it will return to the program menu. Zone Attributes (Edit Zones) Defaults = NA Use this item number to edit the following zone attributes. q 1 Critical Security Zone (Default = 0 [Off]) Enter 0 to turn attribute Off, 1 to turn attribute On. Critical zones require special authority (partition master and full authority codes) in order to be bypassed. q 2 RF Supervisory Time (Default = A [4 hours - Commercial Burg, 24 hours - Home Navigator]) Enter 0 for Supervisory Time A (17049), 1 for Supervisory Time B (1700). q 3 Zone Activity Threshold (Default = 0 [None]) Enter 0 for None, 1 for Threshold 1 (xx018), 2 for Threshold 2 (xx019), 3 for Threshold 3 (xx020). q 4 Hardwire Smoke Verify (Default = 0 [Off]) Enter 0 to turn attribute Off, 1 to turn attribute On. If on, when a hardwire smoke detector is tripped, the panel will remove power for seconds to reset the smoke. If a second trip occurs within 60 seconds, an alarm will sound and a report will be sent to the central station. q Delayed Zone (Default = 0 Off) Enter 0 to turn attribute Off, 1 to turn attribute On. (see 17117). q 6 Floor (Default = 0 [None]) Enter the floor number the zone resides on (1 90 above ground, below ground, 0 = None) (see 17074). q 7 not supported. q 8 not supported. q 9 not supported. q 10 Warning message index (Default = 0 [None]) Enter the desired warning message (1 ). If learned into zone type 70 it will only play the desired warning message. q 11 Zone Bypass Group (Default = 0 [None]) Enter the desired bypass group number (0 32). This will allow users to directly bypass and unbypass groups of zones. To Edit Zone Attributes: 1. Once in program mode enter The display shows ENTER ZONE NUMBER OR PRESS * TO CANCEL. 2. Enter the desired zone number and press #. The display shows ENTER ATTRIBUTE NUMBER OR PRESS * TO CANCEL. 3. Enter the attribute number from the list above and press #. The display will show the current attribute setting. If desired, change the attribute setting. 4. Press # to apply changes. To edit another attribute repeat step 1. Test Buddies 4700 Default = NA Use this item number to test zone buddies. To Test Buddies: Once in program mode enter The display will show BUDDY TEST MODE. Once the test is complete the display will list buddies (see List Buddies 47006). List Buddies Default = NA Use this item number to list information about existing buddy zones. The system will list the buddy zone number, ID, and latest buddy test results. To List Buddies: Once in program mode enter The display will list all four buddies. q If the buddy doesn t exist, the panel will display BUDDY n INVALID. q If the buddy failed the latest test (4700), the panel will display BUDDY n FAILED. q If the buddy passed the latest test, the signal strength will be displayed. The panel will scroll through and display information about each buddy. To skip forward press #. To exit press *. Once the panel lists all the buddies it will return to the program menu. Zone Delay Time Default = 10 Seconds Set the time delay (in seconds) between a zone being tripped and the trip being processed by the panel. This allows time for a zone to reset. This setting only applies to zones programmed as delayed. To Set Zone Delay Time: 1. Enter the item number. 2. Enter the delay time (1 2 seconds) and press #. 33

36 Programming the Panel I/O Settings Use the following item numbers to specify how inputs and outputs behave. General Input Response Time General Input Response Time General Input Response Time General Input Response Time General Input Response Time General Input Response Time General Input Response Time Defaults = 32 (0.12 Seconds) Each of the seven onboard (snapcard) inputs has a response time. The panel has to see a transition for at least that length of time in order to deem it a trip or restoral. At the panel you enter response times in 16 millisecond increments (actual time = value x 16 ms). To Program a General Input Response Time: 1. Enter the desired item number. 2. Enter a response time (8 2) and press #. Expansion Input Response Time Expansion Input Response Time Expansion Input Response Time Expansion Input Response Time Expansion Input Response Time Expansion Input Response Time Expansion Input Response Time Expansion Input Response Time Defaults = 32 (0.12 Seconds) Each of the eight expansion inputs has a response time. The panel has to see a transition for at least that length of time in order to deem it a trip or restoral. At the panel you enter response times in 16 millisecond increments (actual time = value x 16 ms). To Program an Expansion Input Response Time: 1. Enter the desired item number. 2. Enter a response time (8 2) and press #. General Purpose I/O 1 Direction General Purpose I/O 2 Direction General Purpose I/O 3 Direction 1706 General Purpose I/O 4 Direction General Purpose I/O Direction General Purpose I/O 6 Direction Defaults = 0 (Input) Select the direction of each general purpose input/output. To Program General Purpose Input/Output direction: 1. Enter the desired item number. 2. Enter 1 to set the direction as an output, or 0 to set it as an input. Press # to apply the direction. Activation Interval One-Shot Time A (Default = 4 Seconds) Activation Interval One-Shot Time B (Default = 30 Seconds) Activation Interval One-Shot Time C 1711 (Default = 180 Seconds) Activation Interval One-Shot Time D (Default = 900 Seconds) Specify how long (in-seconds) outputs are activated when the response is set to one-shot. Only those outputs programmed to be one-shot (A, B, C, or D) will be affected by this setting. To Program One-Shot Time: 1. Enter the desired item number. 2. Enter the desired one-shot time duration (1 999) and press #. Output Delay Time (Default = 30 Seconds) Specify how long (in-seconds) output activation is delayed. Only those outputs that are programmed to be delayed will be affected by this setting. To Program the Output Delay Time: 1. Enter the desired item number. 2. Enter the desired delay time (1 999) and press #. Accessory Modules The items below allow you to add, delete, list, and modify SuperBus 2000 devices and settings. Add (Learn) Bus Devices Default = NA Use this item number to force the panel to scan for bus devices once they have been correctly connected to the panel. All SuperBus 2000 devices are added to partition/area 1 initially. Use item number (Bus Device Partition/ Area) to assign devices to different partitions/areas once added. To Force the Panel to Scan for Bus Devices: Once in program mode enter The display will show DEVICES ADDED, then it will list the added devices as shown. DEVICE nn ID xxxxxxxx PARTITION/AREA z Where n is the 2-digit device number (01 62), xxxxxxxx is the 8- digit ID number (address), and Z is the partition/area number (1 8). 34

37 Programming the Panel Delete/Change Bus Device ID Default = NA Use this item number to delete bus devices or change device IDs (replace one device with a new one). If you are deleting bus devices, you must delete them one at a time. Deleting the device does not delete the bus text associated with the deleted device. To delete device text use item number To Delete/Change Device ID: 1. Once in program mode enter The display shows ENTER DEVICE ID OR PRESS * TO CANCEL. 2. Enter the 8-digit device ID of the device you wish to delete/ change (located on module) and press #. 3. The display shows ENTER NEW DEVICE ID OR ENTER 0 TO DELETE. 4. Enter a new device ID or enter 0.. Press #. The panel displays DEVICE ID xxxxxxxx DELETED, or DEVICE CHANGE OK. 6. To delete/change another device ID, repeat the above procedure. Bus Device Text Default = None Use the following guidelines to name bus devices: q Use the item numbers that appear in Table B2 on page 8 for characters and words listed there. q If a desired word does not appear in Table B2, create it using the characters (custom text). q When using words from Table B2, spaces between them appear automatically. When using characters from Table B2 to create words, you must reserve an item number for a space after the word. q Each character or word uses up one item number. For example, a word from the list counts as one item number. A created word (such as BOY S) counts as six item numbers 4 letters, 1 apostrophe, and 1 space. q Only 8 item numbers are allowed for each bus device name, so plan ahead before programming device text. You may need to abbreviate words to avoid running out of item numbers. To Program Device Text: 1. Once in program mode enter The display shows ENTER DEVICE ID OR PRESS * TO CANCEL. 2. Enter the desired device ID (located on module) and press #. The display shows TEXT FOR DEVICE xxxxxxxx IS CURRENT TEXT. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 3. Enter the numbers of the desired characters or words. If you make a mistake press * to start over. 4. Once all numbers have been entered, press # to accept. The display shows the new device text. To Delete Device Text: 1. Once in program mode enter The display shows ENTER DEVICE ID NUMBER OR PRESS * TO CANCEL. 2. Enter the desired device ID number and press #. The display shows TEXT FOR DEVICE xxxxxxxx IS current text. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 3. Enter 000 and press #. The display shows TEXT FOR DEVICE xxxxxxxx IS NO TEXT. List Bus Devices Default = NA Use this item number to list information about existing bus devices. The system will list the device address number, device ID number, and the partition/area number. To List Bus Devices: Once in program mode enter The display will show DEVICE nn, ID xxxxxxxx, PARTITION/AREA n. The panel will scroll through and display information about each device. To skip forward press #. To exit press *. Once the panel lists all the bus devices it will return to the program menu. Bus Device Partition/Area Default = NA Use this item number to assign bus devices to partitions/areas. All bus devices default to partition/area 1. To Assign Bus Devices to Partition/Area: 1. Once in program mode enter The display shows ENTER DEVICE ID OR PRESS * TO CANCEL. 2. Enter the 8-digit device ID and press #. The display shows ENTER PARTITION NUMBER OR PRESS * TO CANCEL. 3. Enter the partition/area number and press #. The display shows DEVICE xxxxxxxx IS IN PARTITION n. If the partition/area is not enabled, the display will show PARTITION NN INVALID. See item number xx068 to enable partition/area(s). Change Transmit Bus ID 4800 Default = NA This item number allows you to change or view the wireless transceiver device ID used to communicate with buddy panels and/or wireless 2-way devices. To Change/View Transmit Bus ID: 1. Once in program mode enter The display shows RADIO ID IS xxxxxxxx, then displays ENTER NEW TRANSMIT ID OR PRESS # TO ACCEPT. 2. Enter the new 8-digit transmit ID or press # to accept the existing ID. The touchpad displays RADIO ID IS XXXXXXXX. List Bus Device Text Default = NA Use this item number to list existing bus device ID numbers and display text. To List Bus Device Text: Once in program mode enter The display will show ID xxxxxxxx ANY DEVICE TEXT. The panel will scroll through and display information about each device. To skip forward press #. To exit press *. Once the panel lists all the bus devices it will return to the program menu. 3

38 Programming the Panel Replace/Delete Bus Device Text ID Default = NA Changes (overwrites) the bus device text with that of another bus device. To Replace/Delete Bus Device ID: 1. Once in program mode enter The display shows ENTER DEVICE ID OR PRESS * TO CANCEL. If the display shows DEVICE xxxxxxxx INVALID, there is no device text associated with the device ID you entered. 2. Enter the 8-digit device ID of the device you wish to replace/ delete (located on module) and press #. 3. The display shows ENTER NEW DEVICE ID OR ENTER 0 TO DELETE. 4. Enter the new device ID or enter 0. Press #. Program LED Module Default = NA Use this item number to program LED modules (driver boards). To Program LED Modules: 1. Once in program mode enter The display shows ENTER DEVICE ID OR PRESS * TO CANCEL. 2. Enter the 8-digit device ID number and press #. The display shows ENTER LED NUMBER OR PRESS * TO CANCEL. 3. Enter the desired LED number (1 128) and press #. The display shows LED TYPE IS N. ENTER NEW LED TYPE OR PRESS # TO ACCEPT. 4. Enter the desired LED type (0 1) from Table B10 on page 100 and press #. The display shows LED DATA IS n. ENTER NEW LED DATA OR PRESS # TO ACCEPT.. Depending on the LED type, enter the desired LED data (see Table B10) and press #. 6. To program another LED group, go back to step 1. To exit back to the program menu, press *. Delete/Replace LED Module Default = NA Use this item number to delete LED modules or change device IDs. This setting allows you to replace a malfunctioning LED module without having to reprogram LED settings. To Delete/Replace LED Module: Deleting the module does not delete the bus text associated with the deleted device. To delete device text use item number Keypad Idle Text 4900 Default = None Use the following guidelines to add keypad idle text to the panel. This is the custom text displayed when the partition/area is not armed, not in alarm, and not in a trouble condition. q Use the item numbers that appear in Table B3 on page 91 (2 digit display descriptors) for characters. q When using characters from Table B3 to create words, you must reserve an item number for a space after the word. q Each character or word uses up one item number. For example a word (such as EAST WING) counts as nine item numbers 8 letters and 1 space. q 63 item numbers are reserved for display text in each partition/area so plan ahead before programming text. You may need to abbreviate words to avoid running out of item numbers. To Program Keypad Idle Text: 1. Once in program mode enter The display shows ENTER PARTITION/AREA NUMBER OR PRESS * TO CANCEL. 2. Enter the desired partition/area number and press #. The display shows ENTER DISPLAY NUMBERS OR PRESS * TO CANCEL. 3. Enter the numbers of the desired characters. If you make a mistake press * to start over. 4. Once all numbers have been entered, press #. To Delete Keypad Idle Text: 1. Once in program mode enter The display shows ENTER PARTITION NUMBER OR PRESS * TO CANCEL. 2. Enter the desired partition/area number and press #. The display shows ENTER DISPLAY NUMBERS OR PRESS * TO CANCEL. Press #. Programmable Output Settings Whenever possible, use Advent Downloader to program outputs. All non-x-10 outputs must be mapped to the desired bus module, SnapCard, or panel relay/general purpose output. Due to the complexity of this procedure, it is recommended to program outputs using Advent Downloader. Output text may easily be programmed at a panel touchpad. 1. Once in program mode enter The display shows ENTER DEVICE ID OR PRESS * TO CANCEL. 2. Enter the 8-digit device ID of the device you wish to delete or replace (located on module) and press #. 3. The display shows ENTER NEW DEVICE ID OR ENTER 0 TO DELETE. 4. Enter a new device ID or enter 0. Press #. The panel displays DEVICE ID xxxxxxxx DELETED, OR DEVICE CHANGE OK.. To delete or replace another LED module, repeat the above procedure. 36

39 Programming the Panel Output Configuration 000 Default = NA Use the procedure below for mapping outputs. To Program an Output: 1. Once in program mode enter 000. The display shows ENTER OUTPUT NUMBER OR PRESS * TO CANCEL. 2. Enter the desired 3-digit output number from the following choices: q , programmable outputs. q 01 04/08, Interior siren outputs (1 per partition/ area). q /608, Exterior siren outputs (1 per partition/ area). q /708, Strobe outputs (1 per partition/area). 3. Press #. The display shows OUTPUT TYPE IS n. ENTER NEW TYPE OR PRESS # TO ACCEPT. 4. Enter the output type from the following choices: q Enter 1 for a Bus Module Output. q Enter 3 for a SnapCard Output. q Enter 4 for an Panel Output.. Press #. The display shows OUTPUT DATA n IS nnnnnnnn. ENTER OUTPUT DATA n OR PRESS # TO ACCEPT. 6. Based on the output type, enter the required data from the choices below. Bus Module Output Enter the 8-digit device ID and press #. Enter 1 + #Áfor output data 4. Output data shows The first 4 places represent outputs 1-4 on a 4 Relay Output Module. Choose which output(s) to activate. For example, entering activates outputs 1 and 4 on a 4 Relay Output Module. SnapCard Output Output data shows The first 4 places represent an output SnapCard mounted in the lower slot (SnapCard 1). The last 4 places represent an output SnapCard mounted in the side slot (SnapCard 2). Choose which output(s) to activate. For example, entering would activate the second output on SnapCard 1, and the third output on SnapCard 2. Panel Output Output data shows The first 6 places represent general purpose outputs 1 6, 7 represents the panel interior siren output, and 8 represents the panel exterior siren output. Choose which output(s) to activate. For example, entering activates onboard outputs 1 and 2. Menu Output Text Default = None Use the following guidelines to name the X-10 and non-x-10 menu output numbers that appear in the Lights/Devices user menus. q Use the item numbers that appear in Table B2 on page 8 for characters and words listed there. q If a desired word does not appear in Table B2, create it using the characters (custom text). q q q Only preprogrammed words from Table B2 can be spoken by the panel. Silence takes the place of any created words when the panel voice speaks. However, created words are displayed just like preprogrammed words. When using words from Table B2, spaces between them appear automatically. When using characters from Table B2 to create words, you must reserve an item number for a space after the word. Each character or word uses up one item number. For example, a word from the list counts as one item number. A created word (such as BOY S) counts as six item numbers 4 letters, 1 apostrophe, and 1 space. Only 8 item numbers are allowed for each output name, so plan ahead before programming output text. You may need to abbreviate words to avoid running out of item numbers. To Program Output Text: 1. Once in program mode enter The display shows ENTER OUTPUT NUMBER OR PRESS * TO CANCEL. 2. Enter the desired output number as follows: q Partition 1 1 thru 40 q Partition 2 41 thru 80 q Partition 3 81 thru 120 q Partition thru 160 q Partition 161 thru 200 q Partition thru 240 q Partition thru 280 q Partition thru 320 Entering an output number outside the range for a given partition is indicated by an Invalid message. 3. Press #. The display shows TEXT FOR OUTPUT nn IS CURRENT TEXT. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 4. Enter the numbers of the desired characters or words. If you make a mistake press * to start over.. Once all numbers have been entered, press # to accept. The display shows the new output text. To Delete Output Text: 1. Once in program mode enter The display shows ENTER OUTPUT NUMBER OR PRESS * TO CANCEL. 2. Enter the desired output number and press #. The display shows TEXT FOR OUTPUT nn IS CURRENT TEXT. ENTER TEXT NUMBERS OR PRESS # TO ACCEPT. 3. Enter 000 and press #. The display shows TEXT FOR OUTPUT nn IS NO TEXT. 37

40 Programming the Panel Alarm Settings Alarm settings specify how the panel behaves during certain alarm situations. Alarm settings are global. Alarm Messages Played at High Volume Default = 1 (On) Choose whether or not you want alarm messages (on voice siren) always played at high volume. If not, they will be played at normal volume. Auxiliary/Medical alarm messages are never sounded at high volume regardless of this setting. To Set Alarm Message Volume: 1. Once the item number has been entered, enter 1 for on (high volume), or 0 for off (normal volume). 2. Press # to apply the new setting. Evacuation Messages Default = 0 (Off) Choose whether or not fire alarm evacuation audio messages are played during fire alarms. If off, evacuation messages will not play during fire alarms. To Turn Evacuation Messages On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Unsilence Alarm Default = 0 (Off) Choose whether or not to enable unsilencing of alarm after silencing period expires. If on, a silenced fire alarm will resound. The silencing period can be set using the Time Fire Alarm is Silenced setting (17111) below. To Turn Unsilence Alarm On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Time Fire Alarm is Silenced Default = 30 Seconds Specify the amount of time (in seconds), for which sirens are silenced during a fire alarm (after a user enters a valid access code). The alarm will not unsilence if Unsilence Alarm setting (17126) is set to off. To Set Time Fire Alarm is Silenced: 1. Once the item number has been entered, specify the silence time (1 999). 2. Press # to apply the new setting. Evacuation Message Count Default = 4 Messages Set the number of evacuation messages (0 4) to be played. Evacuation messages are automatically played until the siren times out, the alarm is silenced, or the alarm is canceled. This setting determines the number of evacuation messages played starting with number 1 and up (then repeated). For example, if set to 2, evacuation messages 1 and 2 will be played and repeated. In order for the panel to play evacuation messages during fire alarms, the Evacuation Messages setting (17083) must be set to on. To Set Evacuation Message Count: Once the item number has been entered, enter the evacuation message count (0 4) and press #. First Fire Alarm Disarm/Silence Default = Off When set to on, the first code entry will silence a fire alarm and the second code entry will cancel the alarm. If off, the first code entry will silence and cancel the alarm. To Turn First Fire Alarm Disarm/Silence On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Annunciate Earliest Fire Alarm Default = 0 (Off) If on, the panel will annunciate the earliest active fire alarm instead of the most recent, during a multiple fire alarm situation. This option is intended for panels installed in Canada. To Turn Annunciate Earliest Fire Alarm On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Medical Alarm Sound Rhythm Default = 3 (Alternate Modulated) Police Siren Cadence Default = (Steady) Auxiliary Alarm Sound Rhythm Default = 4 (Fast Modulated) Set the alarm type to the desired sound rhythm. Sound Rhythm Format (_ represents 0.12 second sound, represents 0. second sound). q 1 Temporal 3 (silence) (repeat) q 2 Modulated (repeat) q 3 Alternate Modulated (repeat) q 4 Fast Modulated _ (repeat) q Steady (steady on) q 6 Programmable (must program through downloader) To Set Alarm Sound Rhythm: 1. Once in program mode enter the desired item number. 2. Enter the desired sound rhythm (1 6) and press #. 38

41 Programming the Panel System Settings Date, time, and day settings affect all partitions/areas. System Date Default = (1/1/00) This setting lets you adjust the panel calendar to the correct month, day, and year. To Set the System Date: 1. Enter the item number. 2. Enter the correct month (01 12), day (01 31), and year (00 99). For example, enter for September 1, Press #. The display shows the new date. System Time Default = (12:00:00) This setting lets you adjust the panel clock to the correct time. The panel uses a 24-hour clock. For example, to set the time to 4:17:00 PM, enter To Set the System Time: 1. Enter the item number. 2. Enter the correct time 00( ). 3. Press #. The display shows the new time. Detect Receiver Failure Default = 1 (On) When on, (and a wireless commercial transceiver is installed), the panel will detect and indicate wireless receiver failure. This means the panel has received no messages from any wireless zone for 2 hours. To Turn Detect Receiver Failure On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Downloader Callback Default = 0 (Off) Select whether or not to have the panel call back the downloader when the downloader calls out to the panel with a job. This increases security of the downloader sessions by insuring that all downloads are performed by a Downloader that is connected to one of the panel s programmed Downloader phone numbers. To Turn Downloader Callback On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. System Day of Week Default = (Saturday) This setting lets you adjust the panel to the current day of week. Day of week is automatically set when system date is set (for dates in 21st century). Day Format: q 0 Monday q 4 Friday q 1 Tuesday q Saturday q 2 Wednesday q 6 Sunday q 3 Thursday To Set the System Day of Week: 1. Enter the item number. 2. Enter the day of week using the above format (0 6) and press #. Time Format Default = 0 (Off) This setting allows you to choose whether the panel time format is in 12- (AM and PM) or 24-hour format. If on, the panel will announce and display the time in 24-hour format. To Turn Time Format On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Phone Off-Hook is Activity Default = 1 (On) Select whether or not a phone off-hook condition is considered an activity. See no activity internal (xx009) For residential use only. To Turn Phone Off-Hook is Activity On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. RF Supervisory Time A (Default = 4 Hours - Commercial Burg, 24 Hours - Home Navigator) RF Supervisory Time B 1700 (Default = 24 Hours- Commercial Burg, 4 Hours - Home Navigator)) The RF Supervisory Time is the time (in hours) in which the panel must receive a transmission from a wireless zone. If the panel does not receive a transmission within this time window, a trouble report occurs. Advent panels have two RF Supervisory Times (A and B). All wireless zones default to using Supervisory Time A. Use to change Supervisory Time. To Set RF Supervisory Time: 1. Enter the desired item number. 2. Enter the RF Supervisory Time in hours (2 24). 3. Press # to apply the new setting. 39

42 Programming the Panel Automatic Battery Test Interval Default = 1 (4 Hours) Select the time interval between automatic battery tests: q 1 = 4 hours q 0 = 24 hours To Set Automatic Battery Test Interval: 1. Once the item number has been entered, enter 1 for every 4 hours, or 0 for every 24 hours. 2. Press # to apply the new setting. High Rise Installation Default = 0 (Off) Set to on when the panel is installed in a high rise building. This will enable zones to have floor attributes. When on, any zone not programmed with a floor attribute will not turn on all outputs with a fire on floor condition programmed. When off, any zone not programmed with a floor attribute will turn on all outputs with a fire on floor condition programmed. To Turn High Rise Installation On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Enable RF Jam Detect Default = 1 (On) Select whether or not the panel will detect an RF jam. If enabled, a RF Jam trouble condition will be generated whenever the background noise level exceeds the received signal strength for any wireless zone. This setting must be set to on in commercial fire and burglary systems. To Turn RF Jam Detect On/Off: 1. Once the item number has been entered, enter 1 for on (jam detection), or 0 for off (no jam detection). 2. Press # to apply the new setting. Long Range Radio 1707 Default = 0 (Off) Select whether or not you want to enable long range radio (if connected to panel). This option can only be programmed through Advent Downloader. Commercial/Residential Option Default = 0 (Home Navigator), 1 (Commercial) This option controls the names of arming levels 2 and 3. When set to commercial (1), level 2 is called Perimeter, level 3 is called Full. When set to residential (0), level 2 is Home and level 3 is Away. q o 1 = 4 hours q 0 = 24 hours To Set commercial/residential option: 1. Once the item number has been entered, enter 1 for commercial, or 0 for residential. 2. Press # to apply the new setting. Report System Events Default = 1 (On) This setting determines if system events are reported to the central station. To Turn Report System Events On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. System Report Time (STIME) Default = Random Enter the time of day (in 24-hour format) when an automatic phone test to the central station is performed. To Set the System Report Time: 1. Enter the desired item number. 2. Enter the 4-digit system report time (00:00-23:9) and press # to apply the new setting. Percent Full History Buffer Reports Default = 80 Percent This setting allows you to specify how full (percent) the history buffer may get before generating history buffer full trouble condition. Another trouble is generated when the history buffer overflows. To Set History Buffer Percent: 1. Once in program mode enter the item number. 2. Enter the desired percentage (10 100) and press #. Percent Full Report Buffer Reports Default = 80 Percent This setting allows you to specify how full (percent) the report buffer gets before forcing early reporting of delayed low priority events. No trouble is generated until the report buffer overflows. To Set Report Buffer Percent: 1. Once in program mode enter the item number. 2. Enter the desired percentage (10 100) and press #. Partition/Area Text Speech 1712 Default = 1 (On) If on, partition/area text (49004) will be displayed on touchpads and spoken over speakers. If off, partition/area text will only be displayed on touchpads. To Turn Partition/Area Text Speech On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. 40

43 Programming the Panel Enable Daylight Savings Time Adjust Default = 1 (On) This setting allows you to select whether or not the panel adjusts to daylight savings time. If on, the clock makes daylight savings adjustments at 2:00 AM on the first Sunday in April and the last Sunday in October. The time will spring ahead from 01:9 to 03:00 or fall back from 01:9 to 01:00. To Turn Daylight Savings Time Adjust On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Print System Events Default = 1 (On) This setting allows you to select whether or not to print system events. This setting only enables the printing of system events. See Print Partition/Area Events setting (xx091) to enable partition/area event printing. To Turn Print System Events On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Print Line Feed after Carriage Return Default = 1 (On) This setting allows you to select whether or not to print a line feed after a carriage return. This will tell the printer to print a line feed, creating an extra blank line. Some printers have an auto line feed setting. If the printer adds its own extra line feed, disable this setting so that it doesn t print extra blank lines. Check the printer manual for details. To Turn Print Line Feed after Carriage Return On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. AC Report Delay Default = 6 Hours This setting allows you to select the hours to delay (in addition to random 0 30 minute delay) before the panel reports AC power failure to the central station. To Set AC Report Delay: 1. Once in program mode enter the item number. 2. Enter the desired delay (0 36) and press #. Low Battery Voltage Default = 180 (10.6V) This setting allows you to specify the backup battery voltage at which low battery trouble is generated (set in 1/17 volt units). To Set Low Battery Voltage: 1. Once in program mode enter the item number. 2. Enter the desired voltage ( [ V]) and press #. Battery Restored Voltage Default = 196 (11.6V) This setting allows you to set the voltage at which a low battery trouble restoral is generated (set in 1/17 volt units). To Set Battery Restoral Voltage: 1. Once in program mode enter the item number. 2. Enter the desired voltage ( [ V]) and press #. Start Shutdown Battery Voltage Default = 19 (9.4V) This setting allows you to set the backup battery voltage at which a system shutdown (during an AC power failure) is started (set in 1/17 volt units). To Set Start Shutdown Voltage: 1. Once in program mode enter the item number. 2. Enter the desired voltage ( [ V]) and press #. Printer Supports Epson ESC/P Protocol Default = 1 (On) Turn this setting on if the printer attached to the panel supports ESC/P protocol. Check the printer manual for details. To Turn Epson ESC/P Protocol On/Off: 1. Once the item number has been entered, enter 1 for on, or 0 for off. 2. Press # to apply the new setting. Cancel Shutdown Battery Voltage Default = 176 (10.4V) This setting allows you to set the backup battery voltage at which a system shutdown (during an AC power failure) is canceled (set in 1/17 volt units). To Set Cancel Shutdown Voltage: 1. Once in program mode enter the item number. 2. Enter the desired voltage ( [ V]) and press #. 41

44 Programming the Panel Miscellaneous Settings AC Stable Time Default = 8 Seconds This setting allows you to specify the time (in seconds) that AC power must be lost or restored before a trouble, or trouble restoral is generated. These events are not reported immediately (see 17041). To Set AC Stable Time: 1. Once in program mode enter the item number. 2. Enter the desired time (0 200) and press #. Downloader Account Number Default = The Downloader Account Number is used to identify the panel to Advent Downloader. To Enter a Downloader Account Number: 1. Once the desired item number has been entered the current account number will be displayed. 2. Enter an 8-digit number (0 9) and press #. AC Frequency Default = 0 (60 Hz) This setting allows you to choose the AC frequency that is powering the panel. To Set the AC Frequency: 1. Once in program mode enter the item number. 2. Enter 1 for 0 Hz (off), or 0 for 60 Hz (on). 3. Press # to apply the new setting. Reset Panel 0001 Default = NA This setting allows you to clear any errors the panel may have by rebooting the system. All settings will remain unchanged. To Reset the Panel: 1. Enter the installer code. 2. Enter Press 99 and then #. Wait about a minute for the panel to reset. Latitude Adjustment Default = 0 Degrees This setting allows you to specify the latitude (in degrees) where the panel is located. This information is then used by the panel when automatically adjusting sunrise/sunset schedules. To Set the Latitude: 1. Once in program mode enter the item number. 2. Enter the desired latitude (0 6) and press #. On Premises Pager ID On Premises Pager ID Defaults = This setting allows you to specify 7-digit pager IDs that will identify the 2 different pager groups in a local paging network. To Specify On Premises Pager IDs: 1. Once in program mode enter the item number. 2. Enter the desired 7-digit (0 9) pager ID and press #. Software/Hardware Version 0003 Default = NA This setting allows you to view and identify panel hardware and software version. To View System Version: 1. Enter the installer code. 2. Enter The panel displays SYSTEM ID nnnnnnnn VERSION n.nn nnn.nnn PANEL TYPE n SNAPCARD n n. Panel Type Formats: 0 Commercial Burg-20 not used 1 Home Navigator not used 2 Commercial Fire-20 7 Commercial Burg Home Navigator-20 8 Commercial Fire not used SnapCard Type Formats: 0 none quad smoke loop 1 not used 6 not used 2 NAC 7 not used) 3 8Z input 8 4z input, 2 relay output 4 4 relay output Clear History Buffer 0004 Default = NA This setting allows you to clear the history buffer. To Clear History Buffer: 1. Enter the installer code. 2. Enter The display shows HISTORY BUFFER CLEARED. 42

45 Programming the Panel Set Holiday A List 0008 Set Holiday B List 0009 Defaults = NA Holiday lists allow you to set up time periods when regular schedule hours vary. A holiday is defined as one day. A separate holiday must be added in order to span over consecutive days. Once set up, users can incorporate holidays into schedules. Each partition/area has 2 lists (A and B) and each list has up to 8 holidays. Document holidays in the User s Guide. To Add a Holiday: 1. Enter the installer code. 2. Enter the desired item number. The display shows ENTER PARTITION/AREA NUMBER OR PRESS * TO CANCEL. 3. Enter the partition/area number (1 8) and press #. The display shows ENTER HOLIDAY NUMBER OR PRESS * TO CANCEL. 4. Enter the desired holiday number (1 8) and press #. The panel display shows HOLIDAY DATA IS CURRENT DATA.. Enter a 2-digit month (01-12), a 2-digit day (01 31), and press #. For example, if the holiday fell on July 4, you would enter The display shows the new holiday setting. To Delete a Holiday: 1. Enter the installer code. 2. Enter the desired item number. The display shows ENTER PARTITION/AREA NUMBER OR PRESS * TO CANCEL. 3. Enter the partition/area number (1 8) and press #. The display shows ENTER HOLIDAY NUMBER OR PRESS * TO CANCEL. 4. Enter the desired holiday number (1 8) and press #. The panel display shows HOLIDAY DATA IS current data.. Enter 0 + #. The display shows HOLIDAY DATA IS NO DATA. Set Event Configuration and Alarm Masks 0010 Defaults = NA This setting allows you to specify how you want events reported. Whenever possible, use Advent Downloader to set configuration masks. Event masks are represented by an eight-digit event mask number where 0 = off and 1 = on. For example, if an event mask reported to phone 1, phone 2, history buffer, and was high priority, it would be represented as (see event mask formats below). If you wanted the same event mask to stop reporting to phone 2, you would change the event mask number to Notice how the place holder for phone 2 was changed from a 1 (on) to a 0 (off). (From to ). Event Mask Formats: 1 Reporting Phone 1 Pager 2 Reporting Phone 2 6 Report to Backup 3 Print 7 (not used) 4 History Buffer (Store) 8 High Priority To Set a Configuration Mask: 1. Enter The display shows ENTER EVENT GENERAL TYPE OR PRESS * TO CANCEL. 2. Enter the event general type (1 19) using Table B8 on page 97, then press #. The display shows ENTER EVENT SPECIFIC TYPE OR PRESS * TO CANCEL. 3. Enter the event specific type using Table B8, and press #. The display shows ENTER PARTITION NUMBER OR PRESS * TO CANCEL. 4. Enter the desired partition/area (1 8) and press #. The display shows the eight-digit event mask, then ENTER NEW EVENT MASK OR PRESS # TO ACCEPT.. Enter the desired 8-digit event mask (0 = off, 1 = on, and 2 = unchanged), then press #. Alarm Event Formats: 1 Not Used (leave at default) 2 Not Abortable 6 (leave at default) 3 Reporting Delay (part 1)* 7 (leave at default) 4 Reporting Delay (part 2)* 8 (leave at default) Reporting Delay Formats: 00 = Immediate, 01 = Fire delay, 10 = Panic delay, 11 = Standard delay. To Set an Alarm Event: 1. Enter The display shows ENTER EVENT GENERAL TYPE OR PRESS * TO CANCEL. 2. Enter the event general type (0) and then press #. The display shows ENTER EVENT SPECIFIC TYPE OR PRESS * TO CANCEL. 3. Enter the alarm specific type using Table B8, and press #. The display shows ENTER PARTITION NUMBER OR PRESS * TO CANCEL. 4. Enter the desired partition/area (1 8) and press #. The display shows the eight-digit event mask, then ENTER NEW EVENT MASK OR PRESS # TO ACCEPT.. Enter the desired 8-digit event mask (0 = off, 1 = on, and 2 = unchanged), then press #. Print Zone & Device Information 0012 Default = NA Sends programmed zone and device information to the printer. To Print Zone and Device Information: Enter Zone and Device information will print. 43

46 Remote Downloader Programming Print History Buffer 0016 Default = NA Prints events based on a time range. To Print History Buffer: 1. Enter The display shows ENTER HISTORY START. 2. Enter the desired start date in mm/dd/yy format. For example, if you wanted to print events starting on September 1, 1999 you would enter The display shows ENTER HISTORY STOP. 3. Enter the desired stop date in mm/dd/yy format. Events occurring within that time frame will print. Delete Primary SnapCard 0014 Delete Secondary SnapCard 001 Default = NA This setting enables you to delete a SnapCard when it is being replaced with a different type of SnapCard. All inputs/outputs for the new card must be programmed. If you are replacing the SnapCard with the same type of SnapCard you don t have to perform this procedure and can keep the current input/output settings. To Delete SnapCard Information: 1. Enter the installer code. 2. Enter the desired item number. The panel displays SNAPCARD DELETED. Remote Downloader Programming Although most information can be programmed at the panel, some optional information must be programmed remotely from Advent Downloader. Use the information you recorded in Appendix A to inform the downloading operator of the programming requirements for this system. Advent Downloader Programming The Enable Remote Access setting (17086) must be set to on to allow a remote downloader to call in and connect to the panel. To initiate an upload/download session from the panel: 1. Contact your download station and ask the operator to prepare for an upload/download session. 2. Make sure the panel is connected to a phone line and that premises telephones are on hook (hung up). 3. Enter panel programming and verify/enter the following downloader settings: q Dealer Access Code Must match (in Advent Downloader and at the panel) or be left at default. q Downloader Access Code Must match (in Advent Downloader and at the panel) or be left at default. q Downloader Account Number Must match (in Advent Downloader and at the panel) or be left at default. q yy001 (23001 or 24001) Phone Number Enable Must be on for panel to call the downloader. q yy002 (23002 or 24002) Phone Number At least one downloader phone number must be programmed for panel to call downloader. (Programming the phone number automatically enables it.) 4. Enter install code (0123 default).. For an upload enter 1, a download press 2, and a general upload/download press 3. The session will start and the system will return to the previous arming level. The panel software versions (in Advent Downloader and at the panel) must match. If the panel displays DOWNLOAD FAILURE contact the downloader station to verify the downloader phone number and settings. Installing Line Carrier Devices This section describes how to install X-10 Lamp, Appliance, and Universal Module line carrier (wireless) line carrier devices. Programming the Panel House Code Please see item numbers xx022 and xx023 for information on setting house codes. Installing X-10 Modules When installing X-10 modules: q Use only incandescent lamps with lamp modules. q Do not plug X-10 modules into outlets controlled by a switch. q Do not use extension cords to connect several lamps or appliances to one module. &$87,21 Use X-10 Lamp Modules to control light fixtures do not use X-10 Appliance or Universal Modules. Appliance and Universal Modules are not controlled during an alarm. To install X-10 modules: 1. Plug the lamp or appliance cord into the bottom of the module. 2. Plug the module into a lower AC outlet. 3. Refer to Table B4 and B on page 91 for the house code you programmed into the panel, and then find the letter that corresponds to that house code. Each letter setting represents one panel house code. For example, house code 1 corresponds with A on the X-10 module house dial. 4. Set the house dial on the module to the appropriate letter.. Set the unit number dial from 1 to 16 for the desired response as described in Table B6 on page 92. Adding Lights/Devices to Program Memory There are 40 light/device outputs per partition. Light/ device numbers 1-32 are X-10 modules. Light/device numbers are not X-10 modules and must be mapped to a bus module, snapcard or panel output. Refer to Table B7 on page 93, programming items xx-029 to xx-06 on page 19, and program item 000 on page 38 for information on programming non-x10 outputs. 44

47 Testing the System To add lights or devices to program memory: 1. Press 7. The display shows FEATURES MENU. 2. Enter 3 and the display shows LEARN LIGHTS AND DEVICES. 3. Press 1 to add a light. The panel displays ENTER A LIGHT NUMBER THEN PRESS #. Press 4 to add a device. The panel displays ENTER A DEVICE NUMBER THEN PRESS #. 4. Enter the desired light or device number (1 40) and press #. The display shows LIGHT/DEVICE nn ADDED.. To add another light or device, enter the desired light or device number and press #. 6. To exit press * + *. To delete lights or devices from program memory: 1. Press 7. The display shows FEATURES MENU. 2. Enter 3 and the display shows LEARN LIGHTS AND DEVICES. 3. Press 2 to delete a light. The panel displays ENTER A LIGHT NUMBER THEN PRESS #. Press to delete a device. The panel displays ENTER A DEVICE NUMBER THEN PRESS #. 4. Enter the desired light or device number (1 40) and press #. The display shows LIGHT/DEVICE nn DELETED.. To delete another light or device enter the desired light or device number and press #. 6. To exit press * + *. Testing the System Before testing, it is recommended that you have covers on all modules (mounted outside the cabinet) and the panel cabinet door closed. The testing environment should match the system working environment. This section describes how to perform the following test procedures: q Basic System Commands. q Testing Panel Backup Battery(s). q Testing Hardwired Zone Inputs. q Testing Wireless Sensors. q Testing Outputs. q Testing Optional Lights and Devices (X-10 Modules). q Testing Phone Communication. q Testing Central Station Communication. q Adjusting Touchpad Contrast. You should test the system after installing, servicing, and adding or removing devices from the system. Refer Troubleshooting on page 0 if correct test results are not achieved. Basic System Commands Table 12 describes basic touchpad operating commands. For complete details on system operation, including user programming, refer to the system User Guide. Refer to Table A12 on page 71 for default access codes. Table 12: Basic System Operating Commands Command System Response Indicates current system status CODE Disarms system to OFF CODE Arms system to PERIMETER/HOME CODE Arms system to FULL/AWAY CODE Manually reset smoke sensors Check alarm history 7 + Check event history buffer CODE + Area Area jump Initiates a battery test CODE Initiates a zone test CODE Initiates a phone test CODE Initiates a fire test Testing Panel Backup Battery(s) The panel can both automatically and manually place a test load on the panel backup battery(s) and measure the voltage output. A newly installed battery may require up to eight hours under panel power before an accurate charge indication. To manually test the panel backup battery(s): 1. Press 8. The display shows SYSTEM MENU. 2. Press 8 again to test the battery(s) and display the result. The display will show the battery voltage as BATTERY TEST: 13.8 V (or similar) TO QUIT PRESS *. 3. Press * to end the battery test immediately. The system will automatically ends the battery test after 1 minutes. Testing Hardwire and Wireless Zones/ Sensors It is recommended that you test all hardwired zones and sensors after all programming is completed and whenever a zone/sensor-related problem occurs. While the zone test is a valuable installation and service tool, it only tests zone operation for the current conditions. You should perform a zone test after any change in environment, equipment, or programming. 1. Close and secure the panel door. 2. Make sure all zones and sensors are in their secured (non-alarm) state. 3. Press 8. The display shows SYSTEM MENU. 4. Enter 1 + installer code to initiate the zone test. 4

48 Testing the System. The display shows ZONE TEST ON - PRESS 11 TO QUIT and sounds one 0. second long beep. 6. Actuate/trip and restore each zone/sensor one at a time while monitoring the display. 7. For hardwire zones the system will beep and display [ZONE #] TEST GOOD in confirmation. If the system does not respond, check the zone/sensor wiring or panel programming. For wireless zones the system will beep, and indicate [ZONE #] SIGNAL LEVEL [##] to confirm the zone number tested. (Refer to Table 13 for signal level descriptions.) If the system does not respond, or if the sensor does not meet the minimum requirements, refer to the If a Wireless Sensor Fails the Zone/Sensor Test section. 8. Press to view tested zones. 9. Press to list untested zones. 10. Press to disarm and end testing (if Quik Arm is on). Otherwise, Press and enter your installer access code. 11. Repeat this test for each partition/area. Table 13: Wireless Signal Levels Number Signal Level 0- Weak 6-14 Fair 1-30 Good 31+ Excellent If a Wireless Sensor Fails the Zone/Sensor Test If system does not beep when a sensor is tripped, place an ITI RF Sniffer (60-401) test tool near the wireless sensor when tripping to verify that the sensor is transmitting. Constant beeps from the RF Sniffer indicate a runaway (faulty) wireless sensor. Remove the sensor battery(s) and replace the sensor. If possible, locate wireless sensors within 00 feet of the panel. While a transmitter may have a range of one mile or more out in the open, the environment at the installation site can have a significant effect on transmitter range. Sometimes a change in sensor location can help overcome adverse wireless conditions. To improve wireless sensor communication, you can: q Reorient the sensor, q relocate the sensor, q if necessary, replace the sensor, or q add additional RF transceivers (up to ). To reorient a wireless sensor: 1. Rotate the sensor and test for improved sensor communication at 90 and 180 degrees from the original position. 2. If poor communication persists, relocate the sensor as described below. To relocate a wireless sensor: 1. Test the sensor a few inches from the original position. 2. Move the sensor from the original position and retest until an acceptable location is found. 3. Mount the sensor in the new location. 4. If no location is acceptable, replace the sensor as described below. To replace a wireless sensor: 1. Test a known good sensor at the same location. 2. If the transmission beeps remain below the minimum level, avoid mounting a sensor at that location. 3. If the replacement sensor functions, contact ITI for repair or replacement of the problem sensor. To add RF transceiver(s): Install and wire the RF transceiver module according to the Installation Instructions included with the module and the information provided on page 9 of this manual. A total of transceivers may be used. Testing Outputs and Sirens All outputs (onboard, SnapCard, output module, and X-10) should be tested to verify configuration programming. &$87,21 Inform the central station of the test before activating outputs that trigger from an alarm condition. 1. Contact the central station to inform them you are testing the system. 2. Verify that all wiring at the panel and output devices is correct. 3. Activate the appropriate device to trigger each output as programmed. 4. Verify that each output responds according to the programmed configuration. For outputs that trigger sirens, verify that the correct alarm sounds are produced from these sirens. Table 14 describes the system alarm sounds you should hear from each alarm event (based on defaults).. Contact the central station when you are finished testing. Table 14: Alarm Types and Sounds Alarm Type Alarm Sound Fire Repeating series of three beeps (temporal 3) Police/Intrusion Continuous tone Auxiliary Rapid beeps Testing Lights and Devices (menu controlled outputs) Refer to Table B6 in Appendix B for X-10 lamp, appliance, and universal module response operation. 46

49 Testing the System Lights and devices must be added (learned) before they can be accessed using the Lights or Devices menus. To test lights and devices: 1. Press 4 to test lights or to test devices. The display shows ENTER A LIGHT/DEVICE NUMBER THEN PRESS #. 2. Enter the desired light or device number to test and press #. 3. Press 1 to select Turn [selected light or device] on now. 4. Verify that the light or device is on.. Press 2 to select Turn [selected light or device] off now. 6. Verify that the light or device is off. 7. Press the Lights On or Lights Off buttons twice to turn all lights on the first house code on or off at the same time. Appliance and universal X-10 modules, if any, are all turned off by pressing Lights Off but are not turned on by pressing Lights On. 8. Repeat steps 2 6 for remaining light or device numbers that are used in all partitions/areas. 9. Press * to return to the main menu. Testing Phone Communication Perform a phone test to check phone communication between the panel and the central station. To perform a phone test: 1. Contact the central station to inform them that you are testing the system. 2. Make sure all premises telephones are on-hook (hung up). 3. Press 0. The display shows PHONE MENU. 4. Press 1 + primary access code + #. The display shows PHONE TEST. Refer to Table A12 on page 4 for default access codes.. Wait for the system to dial and test all programmed telephone numbers. 6. The panel indicates PHONE TEST OK for each phone number successfully tested. 7. Press * quit the phone test. If NUMBER n TEST FAILURE is indicated, press * to quit the test and refer to the Troubleshooting section. Testing Central Station Communication After performing zone and phone tests, check that the system is reporting alarms successfully to the central station and pager(s). &$87,21 Be sure to contact the central station before activating outputs/zones that trigger an alarm condition. To test communication with the central station: 1. Call the central station and tell the operator that you will be testing the system. 2. Arm the system. 3. Test each touchpad, wireless panic button, and trip all of the sensors. Verify that the appropriate system indications and alarms are working correctly. 4. Make sure that you test all programmed central station phone numbers, and all partitions/areas.. When you finish testing the system, call the central station to verify that all of the correct alarms were received. Check pager displays to verify that reports were received. Adjusting Touchpad Display Contrast Touchpad displays can be adjusted for easier viewing to help compensate for lighting conditions in the touchpad location. The contrast adjustment lightens or darkens the text. When performing the procedure below you may get a Bus Communication Failure. This is because the panel takes the touchpad off-line when adjusting the contrast. To adjust display contrast: 1. Enter configuration mode by pressing the D and 6 buttons together for at least two seconds. The display shows DA nnn. 2. Press and release the 1 and 2 buttons together repeatedly until the desired contrast level is displayed. 3. Press * and the display briefly shows DONE, then shows the time and date. For information on adjusting display backlighting and brightness, please see the specific Advent panel User Guide. Vacuum fluorescent displays do not have a contrast adjustment. 47

50 Troubleshooting Troubleshooting This section describes what to do if you experience problems with system operation. If after performing the troubleshooting procedures the panel still malfunctions, please call Technical Support at Feature Problem Solution Access Codes Invalid Code or Invalid Authority is indicated. Duress Code 1. Check that access code is valid or is within use/time limits. 2. Special dealer access code is required for some system programming. 3. Check that code used has sufficient authority to perform the item requested. Customer cannot remember access code(s). 1. Check your records or downloader database to see if you have the customer s access code(s) on file. 2. If downloading software is available, read the panel access code(s) using the downloader. Installer cannot remember install code. 1. Check your records or downloader database to see if you have the install code on file. 2. If downloading software is available, read the panel access code(s) using the downloader. 3. If the panel has no access to downloading, clear memory (to defaults) and reprogram the panel locally. Dealer access codes are not erased by clearing memory. Access code stops working. Optional duress code is not working. Arming/Disarming System won t arm. Batteries 1. Check for valid access code or that code use/time limits have not expired. 2. Check for proper partition/area and code selection. Check for valid code. (See List Access Codes feature.) 1. If arming to Perimeter/Home, make sure all monitored perimeter doors and windows are closed or bypassed. 2. If arming to Full/Away, make sure all perimeter and interior zone sensors are closed or bypassed. 3. Check system status (press 1 + 9) for an indication of the problem. System won t disarm. 1. Check for proper access code. 2. Check the access code authority setting. Main battery and/or main battery failure is indicated. Check the panel backup battery(s) and connections and replace if necessary. Also, refer to the Panel - Power LED section in this table. Zone [zone #] low battery is indicated. Replace the indicated sensor battery. Bypassing Fire zones cannot be bypassed. Fail and/or Invalid is indicated when you attempt to bypass a zone. Zone may already be bypassed, or you are trying to bypass a 24-hour zone that cannot be bypassed. System won t automatically unbypass closed zones. Check that the Unbypassing feature is enabled in programming. 48

51 Troubleshooting Feature Problem Solution Bypassing (continued) Central Station Reporting Devices System only allows a certain number of zones to be bypassed. Check Bypassing Limit feature programming for desired number. Central station is not receiving reports from panel. 1. Perform a phone test. If phone test fails, follow the remaining steps 2. Check that the DB-8 Cord is plugged into the panel phone jack and into the RJ-31X/CA-38A jack. 3. Check for proper RJ-31X/CA-38A jack to phone line wiring. 4. Verify with the central station operator that the correct receiver line phone number is programmed into the panel. Reprogram the phone number and retest if necessary.. Verify that the correct phone reporting format is being used. 6. Verify account number settings for each partition/area and for system. 7. Replace faulty RJ-31X/CA-38A jack. 8. Replace faulty DB-8 cord. 9. Check that the premises phone line is working. (See X-10 Modules, Hardwire Outputs, or 4 Relay Output Module). Dual Phone Line Module Module bus status LED stays off. False Alarm 1. Check module and panel power (Green LEDs on). 2. Check SuperBus wiring and connections. 3. Check that the module is programmed (added/learned) into panel memory. Add the module if necessary. Module bus status LED stays on. 1. Reinitialize panel and module by turning panel power off and back on. 2. Module circuit failure. Replace the module. Module bus status LED blinks, but phones don t work. 1. Check phone wiring and connections. 2. Check that the module is programmed (added/learned) into panel memory. Add the module if necessary. Module phone line status LED is on. Check for phone line failure or phone wiring and connections for that line. Phones connected to module work intermittently. 1. Check module and panel (Green LEDs on). 2. Check Superbus wire routing and length. (Shielded cable may be required on very long or noisy wire runs.) 3. Check panel/module programming. Only one module phone line works. Alarm is being sent by mistake. Only 1 phone line module is allowed. Enter the access code immediately to cancel the alarm. This command aborts the alarm report if done within seconds (alarm report delay time [xx012, xx013, or xx014]) after alarm activation (Dialer Abort feature must be on). The system will indicate Report Canceled and the report will not be sent to the monitoring station. If setting xx089 is set to on. Some alarms such as Fire alarms will not be aborted. 49

52 Troubleshooting Feature Problem Solution Hardwire Alphanumeric Touchpad Touchpad displays Touchpad Not Enrolled and does not respond to buttons. Enter panel programming mode by entering and the install code at a working touchpad or from a telephone. Enter item number and enroll the new touchpad into panel memory. If no touchpads are enrolled into the panel s memory, remove then restore panel power. All touchpads will be enrolled. Touchpad displays ********** and does not respond to button presses. Check for SuperBus miswiring. Touchpad appears dead (no display or response to buttons). Hardwire Inputs No inputs detected. 1. Check that the wiring connector is plugged into the back of the touchpad and into the panel bus connector. 2. Check SuperBus wiring for opens or shorts. 3. Check panel power. 1. Check panel programming of all general purpose inputs/outputs. 2. Check all input device wiring and connections. One input is never detected. 1. Check panel programming of general purpose input/output. 2. Check input device operation. 3. Check input device wiring and connections. Wrong input is detected. Hardwire Outputs No outputs activate. 1. Check panel input programming for input. 2. Check input device wiring and connections. 1. Check panel/module programming. 2. Check output wiring and connections. 3. Check panel/module power (green LEDs on). 4. If used, check the optional external supply powering the output devices. One output never activates. 1. Check panel/module programming for that output. 2. Check output wiring and connections. 3. Check that the output programmed trigger event actually occurs. 4. Output relay may have failed or been overloaded. Reprogram to use a different (unused) output or replace the module. Wrong output activates. 1. Check panel output programming. 2. Check output device wiring and connections. Hardwire Sirens/Bells Exterior sirens are not producing alarm sounds. 1. Check for 12 VDC between panel terminals 6 and 7 during alarm (partition/area 1). 2. Check panel main power. 3. Check for correct wiring at the siren and panel terminals. 4. Check exterior siren output programming.. Be sure that there is a siren output in each partition that is used. Exterior sirens produce status sounds. 1. Check for correct wiring at the siren and panel terminals. 2. Check exterior siren output programming. 0

53 Troubleshooting Feature Problem Solution Hardwire Sirens/Bells (continued) Interior bells are not producing sounds. Hardwire Speakers (Voice) Speakers are not producing sounds. 1. Check for 12 VDC between panel terminals 4 and with bell activated (partition/area 1). 2. Check panel main power. 3. Check for correct wiring at the siren and panel terminals. 4. Check interior bell programming.. Be sure that there is an interior bell output programmed for each partition/area that is used. 1. Check for correct wiring (and opens or shorts) at the speaker and panel terminals. 2. Check that required capacitor and end of line (EOL) resistor are installed at the speaker. 3. Make sure that voice volume is correctly programmed. 4. Speaker output is used for partition/area 1 only. Speaker volume too high or low. 1. Make sure that the voice volume is correctly programmed. 2. Check for too many speakers or incorrect speaker impedance. Hardwire Zones Panel does not respond to hardwire zone input. 1. Check that zones are programmed into panel and add if missing. 2. Make sure that zone is set to a restoral-required type or make sure that system is armed to active level before tripping sensor. 3. If it is an optional 8 Input Module zone, check that the module bus status LED is blinking to show communication with panel. 4. Check zone programming for proper partition/area setting. Lights (See also X-10 Modules, Hardwire Outputs, or 4 Relay Output Module) Light fixture using X-10 Lamp Module does not work. Panel See X-10 Modules feature in this table. Panel does not power up. Panel LED is off and alphanumeric touchpad display is dark. 1. Check the AC circuit breaker to be sure the circuit is live. 2. Check that the backup battery is installed correctly, the battery wires are connected, and the AC power transformer is plugged in. 3. Check for proper panel and transformer wiring. 4. Measure the incoming AC voltage at the panel terminals. The voltage should be about 24 VAC between panel terminals 1 and 2. No incoming AC voltage at panel terminals 1 and Check that AC power transformer is not wired into a switched circuit. 2. Remove AC power from the transformer and disconnect the wires from the transformer and the panel. 3. Check transformer to panel wire for short or open circuits. 4. Connect the transformer and check for about 24 VAC at the transformer unconnected terminals. If zero (0) volts, reset the built-in transformer circuit breaker (if it has one) or replace the transformer. 1

54 Troubleshooting Feature Problem Solution Panel (continued) Panel power LED is on constantly, display indicates Main Low Battery or voice sounds Main Low Battery. 1. Check that the panel backup battery is installed correctly, the battery wires are connected, and the AC power transformer is connected. 2. Measure the incoming AC voltage at the panel terminals. It should read about 24 VAC at panel terminals 1 and Remove the panel backup battery power by disconnecting the red (positive) battery wire. 4. Check for 13.6 to 14.2 VDC battery charging voltage between panel terminal 3 (GND) and the disconnected red battery wire.. Check fuse in the red battery wire. 6. Check for 11. to 13.9 VDC battery voltage between the backup battery spade lugs. If the battery voltage is not within the recommended range, allow the battery time to charge or replace faulty battery. When the panel is running a backup battery test, the reading at the connected battery can range from 11.4 to 13.7 VDC. The panel automatically runs a backup battery test once every 4 or 24 hours (programmed test interval) and at STIME. 7. Restore the backup battery power by reconnecting the red wire from the battery. While the AC power transformer is plugged in, the panel automatically charges the battery. While the battery is charging for the first time it is normal for the system to indicate Main Low Battery. This can take a number of hours depending on the initial battery charge. Once the battery reaches full charge as measured while in battery test, trouble indication will stop once cleared by pressing the * button. If the trouble condition persists after 24 hours, replace the backup battery. Panel power LED quickly flashes once a second, and after pressing 1 + 9, the touchpad indicates Main Power Failure. (Panel continues to operate from backup battery.) 1. Check the AC circuit breaker to be sure the circuit is live. 2. Check for proper panel and transformer wiring. 3. Check that the AC transformer is wired to a non-switched circuit. 4. Check that the transformer is supplying AC to the panel. (Transformer internal breaker or fuse may be blown.) Panel power LED blinks. (Panel power is on and receiving AC power). Partitions/Areas Only partition/area one (1) functions. Phones Panel internal failure is detected - service is required: q 3 Blinks - Program memory checksum failure. q 4 Blinks - Voice memory checksum failure. q Blinks - EVAC memory checksum failure. q 7 Blinks - RAM failure. 1. Check that other partitions/areas are enabled. 2. Check that devices are correctly added (learned) into the other enabled partitions/areas. Loss of dial tone on premises phones after wiring the RJ-31X jack or connecting the DB-8 Cord. 1. Wait 2 minutes and try again. The panel may be busy trying to report to the central station receiver. 2. Check the RJ-31X jack wiring. 3. Check the panel connection to the DB-8 cord. 4. Replace the RJ-31X jack.. Replace the DB-8 cord. 6. Perform a phone test after troubleshooting the phone line. Constant dial tone is preventing dial-out on premises phones. Polarity-sensitive phones exist on the premises. Reverse the phone wires connected to the brown and gray wire terminals on the RJ-31X jack. Phone does not work. Disconnect the panel DB-8 Cord from the RJ-31 jack. If the phone still doesn t work, the system is okay and the problem is in the wiring. 2

55 Troubleshooting Feature Problem Solution Phones (continued) System does not respond to remote phone access. Check that Remote Phone Enable panel feature (17086) is set to on. Noisy or radio sounds on phone when system answers. Printer or Automation Module Module bus status LED stays off. 1. Check phone wire routing and connections. 2. Check for good panel ground connection. 1. Check module and panel power (green LEDs on). 2. Check SuperBus wiring and connections. Module bus status LED stays on. 1. Reinitialize panel and module by turning panel power off then on. 2. Module circuit failure. Replace the module. Module bus status LED blinks, but no interface operation. 1. Panel and module are communicating correctly via the SuperBus. 2. Check that device is learned into panel memory. 3. Check panel/module programming. 4. Check module and device cables and connections. RF Transceiver Module (see also, Hardwire Outputs, Wireless Sensors, and Panel) Module bus status LED stays off. Schedules 1. Check module and panel power (green LEDs on). 2. Check SuperBus wiring and connections. 3. Check for proper panel/module power-up initialization. Module bus status LED stays on Reinitialize panel and module by turning panel power off and on Module circuit failure. Replace the module. Module bus status LED blinks, but limited or no module wireless operation. 1. Panel and module are communicating correctly via the SuperBus. 2. Check that transceiver is learned into panel memory. 3. Check panel/module programming. 4. Check antenna and ground connections.. Check for too close of proximity to metal obstructions such as ducting or AC wiring. Limited wireless signal range. 1. Check Commercial RF Transceiver Module antenna and ground connections. (Never bend or cut wireless radio antennas.) 2. Check for too close a proximity to metal obstructions such as ducting or large appliances. 3. Check/change transmitting device orientation to module. Wrong clock time, date, or day indication. 1. Check panel clock/calendar programming. 2. Check panel day of week programming. Schedules don t repeat. Sensors/Zones (see also wireless smoke sensors) Zone # Tamper is indicated. 1. Check panel schedules programming. 2. Check if system clock/calendar has been changed since schedules were programmed. Replace the zone sensor cover if it is off. Trip and reset the sensor. 3

56 Troubleshooting Feature Problem Solution Sensors/Zones (see also wireless smoke sensors) (continued) Tamper Indications Zone # Supervisory Failure is indicated. The zone/sensor is not communicating with the panel. Zone # Trouble Low Battery is indicated. Replace the indicated zone sensor battery. 1. Check that wireless sensor covers are in place. 2. Check that surface tampered wireless PIRs, Smoke, and Sound sensors are securely mounted. 3. Check that hardwired sensor loop end of line (EOL) resistors are installed. 4. Check for hardwire sensor loop shorts or opens.. If panel door is tampered, check that the panel cover is closed. 6. If phone jack is tampered, check that phone line cords are plugged in. 7. Check that Commercial RF Transceiver antennas are not bent, cut, or missing and that antenna and ground connections are tight. 8. Check for multiple incorrect access code entries from touchpad or phone. Trouble Beeps (see also Panel) Check system status for an indication of the problem. Troubles must be individually acknowledged to silence the beeps. Wireless Sensors (also see RF Transceiver Module) The panel does not respond to sensor activity. There are no alarm, chime, or sensor test sounds. 1. Check that the wireless sensor battery is installed. 2. Check the sensor battery for low voltage. Replace batteries if necessary. 3. Use an RF Sniffer tool (60-401) to verify that the sensor is transmitting. 4. Check that the sensor is programmed (added/learned) into panel memory. Add the sensor if necessary.. Check partition/area setting. 6. Verify that both RF Transceiver module antennas are installed and that the connections are tight. The panel responds intermittently to wireless sensor signals. Wireless Smoke Sensor (see also RF Transceiver Module) Beeps once every minute. Wireless Touchpads 1. Rotate the sensor position from 90 to 180 degrees. 2. Mount the sensor in a different location. 3. Verify that both RF Transceiver Module antennas are installed and connections tight. Sensor batteries are low. Replace all of the smoke sensor batteries. Zone # Partial Obsurity Trouble is indicated. Zone # Trouble is indicated. Check for blocked dirty sensor screen and clean if necessary. Replace the zone/sensor cover, if it is off. Trip the sensor. Check for blocked dirty sensor screen and clean if necessary. Zone # Supervisory Failure is indicated. The sensor is not communicating with the panel. Zone # Trouble Low Battery is indicated. Replace the indicated sensor battery. The panel does not respond to wireless touchpad commands. 1. Operate touchpads from different locations to locate areas of intermittent operation. 2. Check and/or replace wireless touchpad battery. 3. Program or reprogram the touchpad(s) into the panel. 4

57 Troubleshooting Feature Problem Solution X-10 Lamp/Appliance Modules Lights or devices controlled by the X-10 Modules are not working. Zones, Loops (See Hardwire Inputs, Sensors.) 1. Check that the light or device is working and the power switch is on. 2. Confirm light or device operation at working outlet. 3. Check that the lights or devices are plugged into X-10 Modules and that the X-10 Modules are plugged into outlets that are not controlled by a switch. If necessary, relocate modules to nonswitched outlets. 4. Check that the HOUSE dial on the X-10 Modules match the house code programmed into the panel.. Check for correct X-10 module unit settings and panel programming.

58 Appendix A: System Configuration Worksheets Appendix A: System Configuration Worksheets Use Table A1 to determine maximum and standby current draw based on the devices connected to the panel. Customer Name Address City County State Zip Phone ( ) Table A1: System Hardwire Devices Part No. Description Qty. Standby Current Draw Standby Current Subtotal Hardwire Sensors/Detectors PIR Motion Detector 10 ma 10 ma Wire Smoke Sensor 100 ua N/A Wire Smoke/Heat Sensor 100 ua N/A Fire Pull Station N/A N/A Hardwire Sirens/Speakers Hardwire Exterior Siren N/A 14 ma Ohm, 1W Speaker N/A N/A SuperBus 2000 Touchpads and Modules (31 Devices per Bus Header) SuperBus 2000 Dual Phone 20 ma 60 ma Line Module (plastic) (metal) SuperBus 2000 Printer Module 30 ma 3 ma SuperBus 2000 RS 232 Automation Module * 3 ma 3 ma SuperBus x20 LCD 7 ma 120 ma Alphanumeric Touchpad SuperBus x20 VFD 7 ma 120 ma Alphanumeric Touchpad SuperBus x20 VFD Fire Alphanumeric Touchpad 7 ma 120 ma (plastic) (metal) SuperBus 2000 RF Commercial Transceiver Module SuperBus Z Hardwire Input Module SuperBus Relay Output Module SnapCards (2 per panel) 0 ma 0 ma 18 ma 3 ma 2 ma 180 ma Input/2 Output SnapCard 10 ma + 2. ma per zone used + 7 ma per smoke loop used + 34 ma per relay used Z Hardwire Input SnapCard 10 ma + 2. ma per zone used + 7 ma per smoke loop used Maximum Current Draw 18 ma 230 ma Maximum Current Subtotal Output SnapCard 6 ma + 34 ma per relay used 130 ma Total Standby Current Draw (must not exceed 10 ma with 1 battery, 80 ma with 2 batteries, or 1.A with 3 batteries for UL systems). Total Maximum Current Draw (must not exceed A). * Not investigated by UL. 6

59 Appendix A: System Configuration Worksheets Determining Maximum Panel Wire Length Example: Using 22 gauge wire to connect the following devices on one wire run (length of cable): Device Current Draw (see note) 1- Hardwire 2-Line Alpha Touchpad = 120 ma 1- RF Transceiver Module = 0 ma 1-8Z Hardwire Input Module = 3 ma Total Device Current Draw = 20 ma Find the total device current draw in the table and match the wire type used. In this example, the maximum recommended wire length is about 14 feet. For longer lengths, use a larger gauge wire. For self- or remotely-powered devices, the maximum recommended wire length is 4,000 feet using 18 gauge or larger wire. Table A2: Max. Wire Length Recommendations* Total Device Current Draw (ma) 22 Gauge (AWG) 18 Gauge (AWG) 16 Gauge (AWG) 14 Gauge (AWG) ,62 2,486 3, ,244 1, Table A2: Max. Wire Length Recommendations* Total Device Current Draw (ma) 22 Gauge (AWG) *Two volt maximum loop voltage drop. Other System Devices 18 Gauge (AWG) 16 Gauge (AWG) 14 Gauge (AWG) Table A3: Wireless Sensors Part No. Description Qty Handheld Wireless Touchpad Learn Mode Door/Window Sensor Learn Mode Recessed Door/Window Sensor Learn Mode Pendant Panic Sensor Wall-Mount Wireless Touchpad Dual Button Panic Sensor Single Button Panic Sensor Rate-of-Rise Heat Sensor Learn Mode Shock Sensor Learn Mode Glass Guard Sensor Learn Mode Slim Line Door/Window Sensor Learn Mode Freeze Sensor Learn Mode Smoke Sensor Learn Mode Smoke Sensor (System Sensor) 2100ARFT Learn Mode Smoke Sensor (ESL) 60 Series Learn Mode Smoke Sensor (ESL) 70 Series Learn Model DS924i PIR Motion Sensor Water-Resistant Panic Sensor Learn Mode Sound Sensor (IntelliSense) Learn Mode Long Life Door/Window Sensor Learn Mode Micro Door/Window Sensor Learn Mode Recessed Micro Door/Window Sensor Table A4: X-10 Module Line Carrier Devices Part No. Description Qty X-10 Universal Module X-10 Appliance Module X-10 Lamp Module 7

60 Appendix A: System Configuration Worksheets Table A: AC Power Transformer and Backup Battery Part No. Description Qty Heavy Duty 12V, 17.2 AH or 18.0 AH Backup Battery Heavy Duty Line Carrier 24 VAC, 100 VA, Class I, 110VAC, 60 Hz AC Power Transformer Heavy Duty Line Carrier 24 VAC, 100 VA, Class II 110 VAC, 60 Hz AC Power Transformer Partition Number Table A6: X-10 Module House and Unit Code Settings Light Device Number Device Type/Location House Code Unit Code* X-10 Modules and Device Settings Use Table A6 to document information about X-10 module and device settings. If you need more room, simply copy this page. * Unit codes affect module responses. 8

61 Appendix A: System Configuration Worksheets Partition/Area Descriptions Use Table A7 to write in information about each partition or area. Partition/ Area No. Table A7: Partition/Area Numbers and Descriptions Description/Location [Display Text]

62 Appendix A: System Configuration Worksheets SuperBus 2000 Device Information Use Table A8 to document information about SuperBus 2000 touchpads and modules. If you need more room, simply copy this table. Table A8: SuperBus Touchpad and SuperBus Module Unit Numbers Device Description Partition/Area Bus Connector (circle one) Bus Address Number (assigned by panel) Unique SuperBus 2000 ID Number (from device label) 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 60

63 Appendix A: System Configuration Worksheets Zone and Sensor Information Use Table A9 to record information about zones and sensors. Table A9: Zone and Sensor Assignments Zone Number Partition Number Zone Type Zone/Sensor Type (circle one) Module Bus ID Number Module Input Number Attributes (N0, NC, Floor No., etc.) Zone/Sensor Text 01 HW/RF 02 HW/RF 03 HW/RF 04 HW/RF 0 HW/RF 06 HW/RF 07 HW/RF 08 HW/RF 09 HW/RF 10 HW/RF 11 HW/RF 12 HW/RF 13 HW/RF 14 HW/RF 1 HW/RF 16 HW/RF 17 HW/RF 18 HW/RF 19 HW/RF 20 HW/RF 21 HW/RF 22 HW/RF 23 HW/RF 24 HW/RF 2 HW/RF 26 HW/RF 27 HW/RF 28 HW/RF 29 HW/RF 30 HW/RF 31 HW/RF 32 HW/RF 33 HW/RF 34 HW/RF 3 HW/RF 36 HW/RF 61

64 Appendix A: System Configuration Worksheets Table A9: Zone and Sensor Assignments (Continued) Zone Number Partition Number Zone Type Zone/Sensor Type (circle one) Module Bus ID Number Module Input Number Attributes (N0, NC, Floor No., etc.) Zone/Sensor Text 37 HW/RF 38 HW/RF 39 HW/RF 40 HW/RF 41 HW/RF 42 HW/RF 43 HW/RF 44 HW/RF 4 HW/RF 46 HW/RF 47 HW/RF 48 HW/RF 49 HW/RF 0 HW/RF 1 HW/RF 2 HW/RF 3 HW/RF 4 HW/RF HW/RF 6 HW/RF 7 HW/RF 8 HW/RF 9 HW/RF 60 HW/RF 61 HW/RF 62 HW/RF 63 HW/RF 64 HW/RF 6 HW/RF 66 HW/RF 67 HW/RF 68 HW/RF 69 HW/RF 70 HW/RF 71 HW/RF 72 HW/RF 73 HW/RF 74 HW/RF 7 HW/RF 62

65 Appendix A: System Configuration Worksheets Table A9: Zone and Sensor Assignments (Continued) Zone Number Partition Number Zone Type Zone/Sensor Type (circle one) Module Bus ID Number Module Input Number Attributes (N0, NC, Floor No., etc.) Zone/Sensor Text 76 HW/RF 77 HW/RF 78 HW/RF 79 HW/RF 80 HW/RF 81 HW/RF 82 HW/RF 83 HW/RF 84 HW/RF 8 HW/RF 86 HW/RF 87 HW/RF 88 HW/RF 89 HW/RF 90 HW/RF 91 HW/RF 92 HW/RF 93 HW/RF 94 HW/RF 9 HW/RF 96 HW/RF 97 HW/RF 98 HW/RF 99 HW/RF 100 HW/RF 101 HW/RF 102 HW/RF 103 HW/RF 104 HW/RF 10 HW/RF 106 HW/RF 107 HW/RF 108 HW/RF 109 HW/RF 110 HW/RF 111 HW/RF 112 HW/RF 113 HW/RF 114 HW/RF 63

66 Appendix A: System Configuration Worksheets Table A9: Zone and Sensor Assignments (Continued) Zone Number Partition Number Zone Type Zone/Sensor Type (circle one) Module Bus ID Number Module Input Number Attributes (N0, NC, Floor No., etc.) Zone/Sensor Text 11 HW/RF 116 HW/RF 117 HW/RF 118 HW/RF 119 HW/RF 120 HW/RF 121 HW/RF 122 HW/RF 123 HW/RF 124 HW/RF 12 HW/RF

67 Appendix A: System Configuration Worksheets Table A9: Zone and Sensor Assignments (Continued) Zone Number Partition Number Zone Type Zone/Sensor Type (circle one) Module Bus ID Number Module Input Number Attributes (N0, NC, Floor No., etc.) Zone/Sensor Text

68 Appendix A: System Configuration Worksheets Table A9: Zone and Sensor Assignments (Continued) Zone Number Partition Number Zone Type Zone/Sensor Type (circle one) Module Bus ID Number Module Input Number Attributes (N0, NC, Floor No., etc.) Zone/Sensor Text

69 Appendix A: System Configuration Worksheets Table A9: Zone and Sensor Assignments (Continued) Zone Number Partition Number Zone Type Zone/Sensor Type (circle one) Module Bus ID Number Module Input Number Attributes (N0, NC, Floor No., etc.) Zone/Sensor Text Menu Lights and Outputs Use Table A10 to document information about menu controlled lights and outputs. Room to document 40 menu controlled lights and outputs is provided below. If you need more room, simply copy this table. Table A10: Menu Lights and Outputs Partition/Area No. Menu Output No. Text Schedule No. 67

70 Appendix A: System Configuration Worksheets Table A10: Menu Lights and Outputs (Continued) Partition/Area No. Menu Output No. Text Schedule No. Programmable Output Type Information Use Table A11 to document information about programmable outputs. Table A11: Programmable Output Types, Event Triggers, Responses, and Locations Partition/ Area No. Output # Event Trigger Response Output Type Location [Display Text] 68

71 Appendix A: System Configuration Worksheets Partition/ Area No. Table A11: Programmable Output Types, Event Triggers, Responses, and Locations (Continued) Output # Event Trigger Response Output Type Location [Display Text] Access Codes and Authority Level Settings Table A12 shows the default access codes and Table A13 shows default authority level settings. Document any changes in the tables. Table A12: Default Access Codes Partition Default Code Authority User # Primary Primary Primary Primary Primary Primary Primary Primary 8 Global 2020 Primary or 9* Installer 0123 Installer 0 * The primary global access code is user # in 4 partition systems, and user #9 in 8 partition systems. Table A13: Authority Level Settings Programming Setting Description Programmable Authority Level Setting* 10 Remote Access Allowed 11 Arming to Off Allowed 12 Arming to Home Allowed 13 Arming to Away Allowed 14 Arming to Special Level 4 Allowed 1 Arming to Special Level Allowed 18 Standard Zone Bypassing Allowed 19 Critical Zone Bypassing Allowed 20 Zone Test Allowed 21 Phone Test Allowed 22 Schedule Menu Access Allowed 1 á á á á á á á á 2 á á á á á á á á 3 á á á á á á 4 á á á á á á á á á á 6 á á á á á 7 8 * Factory defaults shown. Write in actual settings. Primary (prime) authority - of which there is only one per partition/area is required to assign full and duress authorities. Primary, full and duress authority levels (not shown) are not programmable. 69

72 Appendix A: System Configuration Worksheets Item Numbers Index and Record Use Table A14 to document settings. Items are in numercial order. Table A14: Item Numbers Index and Record Item Number Setting Reference and Default Setting Installer Programming Installer/Dealer CODE LTIME Sound Time (p. 17) 12:00 1, 3,, 7, Siren Sound Time (p. 17) 16 min. 1, 3,, 7, Entry Delay (p. 22) 32 sec 1, 3,, 7, Exit Delay (p. 22) 32 sec 1, 3,, 7, Extended Delay (p. 22) 2 min. 1, 3,, 7, Fast Beep Duration (p. 22) 10 sec 1, 3,, 7, Scheduled Arming Period (p. 21) 10 min. 1, 3,, 7, Scheduled Arming Extension (p. 21) 30 min No Activity Tripped After (p. 18) 0 (Not Active) 1, 3,, 7, 1, 3,, 7, No Activity Report Delay (p. 18) min. 1, 3,, 7, Zone Test Time Out (p. 23) 30 min. 1, 3,, 7, Panic Report Delay (p. 19) sec 1, 3,, 7, Alarm Report Delay (p. 19) sec 1, 3,, 7, Fire Report Delay (p. 20) 0 min. 1, 3,, 7, Suspicion Alarm Delay (p. 18) min. 1, 3,, 7, Bypass Limit (p. 21) 20 (all) 1, 3,, 7, Activity Fault Threshold 1 (p. 20) 10 1, 3,, 7, Activity Fault Threshold 2 (p. 20) 30 1, 3,, 7, Activity Fault Threshold 3 (p. 20) 0 1, 3,, 7, Swing Count (Auto Bypass Trips) (p. 21) 3 1, 3,, 7, X-10 House Code 1 (p. 18) default is partition/area number X-10 House Code 2 (p. 18) default is partition/area number + 8 1, 3,, 7, 1, 3,, 7, Enable Level 2 Arming (p. 20) On 1, 3,, 7, Enable Level 3 Arming (p. 20) On 1, 3,, 7, 70

73 Appendix A: System Configuration Worksheets Item Number Enable Level 4 Arming (p. 20) On 1, 3,, 7, Enable Level Arming (p. 20) On 1, 3,, 7, Non X-10 Output 1 (p. 19) None 1, 3,, 7, Non X-10 Output 2 (p. 19) None 1, 3,, 7, Non X-10 Output 3 (p. 19) None 1, 3,, 7, Non X-10 Output 4 (p. 19) None 1, 3,, 7, Non X-10 Output (p. 19) None 1, 3,, 7, Non X-10 Output 6 (p. 19) None 1, 3,, 7, Non X-10 Output 7 (p. 19) None 1, 3,, 7, Non X-10 Output 8 (p. 19) None 1, 3,, 7, Unlock Button Action (p. 23) 4 (arm to level 1) Lock Button Action (p. 23) 9 (arm to closed level) Lights Button Action (p. 23) 1 (toggle all lights) Star Button Action (p. 23) 12 (incremental arming) Lights/Star Button Combination Action (p. 23) 3 (auxiliary panic) Direct Arm Level 3 Action (p. 23) 6 (arm to level 3) Direct Arm Level 1 Action (p. 23) (arm to level 2) Lock/Star Button Combination (p. 23) 16 (do nothing) Disarm/Lights Button Combination (p. 23) 16 (do nothing) Partition/Area Enable (p. 16) Partition 1 On, Partitions 2 8 Off 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, 1, 3,, 7, Light Access Code Enable (p. 19) Off 1, 3,, 7, Device Access Code Enable (p. 19) Off 1, 3,, 7, Latchkey Access Code Enable (p. 19) Off 1, 3,, 7, Keypad Tamper (p. 18) Off 1, 3,, 7, Second Intrusion Causes Report (p. 20) Off 1, 3,, 7, Generate Alarm for Suspicion Trips (p. 18) On Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default Setting 1, 3,, 7, 71

74 Appendix A: System Configuration Worksheets Item Number Zone Tamper Alarm Enable (p. 17) Off 1, 3,, 7, First Trip Local Second Trip Report (p. 18) Off 1, 3,, 7, Fire Tamper Response (p. 17) Off 1, 3,, 7, Auxiliary/Medical Assignment (p. 23) On (auxiliary alarm) 1, 3,, 7, Enable Police Panic Keys (p. 23) On 1, 3,, 7, Auxiliary Medical Panic Keys (p. 23) On 1, 3,, 7, Enable Fire Panic Keys (p. 23) On 1, 3,, 7, Report Partition/Area Events (p. 19) On 1, 3,, 7, Cancel Event Cancels Report (p. 19) On 1, 3,, 7, Second Fire Alarm Ends Reporting Delay (p. 20) On 1, 3,, 7, Print Partition/Area Events (p. 19) On 1, 3,, 7, Auto Forced Arming (p. 21) On 1, 3,, 7, Quick Arm (p. 21) On 1, 3,, 7, Enable Scheduled Arming (p. 20) On 1, 3,, 7, Swinger Bypass Enable (p. 21) On 1, 3,, 7, Automatic Unbypass Enable (p. 21) Off 1, 3,, 7, Exterior Siren Arming Verification (p. 21) Off Local Closing Report Verification (p. 20) Off 1, 3,, 7, 1, 3,, 7, Exit Beeps (p. 22) On 1, 3,, 7, Exit Delay Termination (p. 22) Off 1, 3,, 7, Exit Delay Reset (p. 22) Off 1, 3,, 7, Entry Delay Beeps (p. 22) Off 1, 3,, 7, Local Trouble Annunciation at LTime (p. 17) On Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default Setting 1, 3,, 7, Chime Text (p. 22) Off 1, 3,, 7, Close Chime (p. 23) Off 1, 3,, 7, All Restoral Reports (p. 20) Off 1, 3,, 7, 72

75 Appendix A: System Configuration Worksheets Item Number Exterior Siren Delay (p. 19) Off 1, 3,, 7, Account No. 1 (p. 16) , 3,, 7, Account No. 2 (p. 16) , 3,, 7, Default Keyfob/Schedule Arming Level (p. 20) 3 1, 3,, 7, Default Keyswitch Arming Level (p. 20) 3 1, 3,, 7, System Date (p. 39) 1/1/ System Time (p. 39) 12:00: System Day of Week (p. 39) Saturday System Report Time (STIME) (p. 40) Random General Input Response Times (p. 34) 32 sec Expansion Input Response Times (p. 34) 32 sec Maximum Ring Cycle Time (p. 27) 67 ms Minimum Ring Burst Duration (p. 28) 400 ms Maximum Ring Burst Duration (p. 28) 200 ms Minimum Duration Between Ring Burst (p. 28) 0 Maximum Duration Between Ring Burst (p. 28) 0 Minimum Time Between Burst (p. 29) 2000 ms Maximum Time Between Burst (p. 28) 400 ms Minimum Time Between Ring-Pause-Ring Calls (p. 30) 10 sec Max Time Between Ring-Pause-Ring Calls (p. 31) 30 sec On Hook Hang Up Time (p. 30) 4 sec Local Phone Connect Time (p. 29) 2 sec Local Phone Answer Time (p. 29) 8 sec Time Between Phone Panic Keystrokes (p. 29) 2 sec Minimum Tone Duration (p. 28) 30 ms Minimum Duration Between Tones (p. 28) 0 ms Interval Between Automatic Phone Test (p. 2) 1 day - Commercial, 7 days - Home Navigator 1703 Touchpad Return Time (p. 16) 10 sec AC Stable Time (p. 42) 8 sec Low Battery Voltage (p. 41) 10.6V Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default Setting I/O 1, I/O 3, I/O, I/O 7 I/O 2, I/O 4, I/O 6 1, 3,, 7, 73

76 Appendix A: System Configuration Worksheets Item Number Battery Restored Voltage (p. 41) 11.6V Start Shutdown Battery Voltage (p. 41) 9.4V Cancel Shutdown Battery Voltage (p. 41) 10.4V AC Report Delay (p. 41) 6 hrs Percent Full History Buffer Reports (p. 40) 80 percent Percent Full Report Buffer Reports (p. 40) 80 percent Sound Rhythms (p. 38) Medical alternate modulated, Police steady, Auxiliary fast modulated RF Supervisory Times (p. 39) A 4 hrs, B 24 hrs Answer Phone after XX rings (p. 30) 12 Rings 1703 Cancel Ring-Pause-Ring After XX Rings (p. 31) 3 rings 1704 Minimum Valid Ring Cycles (p. 28) 2 cycles 170 Valid Ring Bursts (p. 28) 1 burst 1706 Local Phone Control Sequence (p. 29) #* Medical, Police, Auxiliary A, B 1707 Phone Device Override Sequence (p. 29) **## 1708 Pager ID (p. 2) On Premises Pager IDs (p. 42) , System Strobe Light Type Amesco General Purpose I/O Direction (p. 34) 0 (input) No Phone Line (p. 2) Off Enable Daylight Savings Time Adjust (p. 41) On Enable RF Jam Detect (p. 40) On Automatic Battery Test Interval (p. 40) 4 hours High Rise Installation (p. 40) Off 1707 Long Range Radio (p. 40) Off Commercial/Residential Option (p. 40) Home Navigator Off, Commercial On Detect Receiver Failure (p. 39) On Alarm Messages Played at High Volume (p. 38) On Phone Police Panic Enable (p. 30) Off Phone Aux/Med Panic Enable (p. 30) Off Phone Fire Panic Enable (p. 30) Off Evacuation Messages (p. 38) On First Fire Alarm Disarm/Silence (p. 38) Commercial Fire On, Commercial Burglary Off Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default Setting 1, 3,, 2, 4, 6 74

77 Appendix A: System Configuration Worksheets Item Number 1708 Enable Local Phone Access in Partition/ Area 1 (p. 29) Off Enable Remote Phone Access (p. 30) On Enable Remote Phone Ring Count (p. 30) On Enable Remote Phone Ring-Pause-Ring (p. 30) On Enable Remote Phone Override (p. 31) On Enable Toll Saver (p. 30) On Phone Off-Hook is Activity (p. 39) On Global Account Reporting (p. 16) Off Enable Phone Line 1/2 DTMF Dialing (p. 24) On Report System Events (p. 40) On Print Line Feed after Carriage Return (p. 41) On Allow Remote Phone Zone Test (p. 31) On Print System Events (p. 41) On Time Format (p. 39) Off (12 hr) Buddy Dial Attempts (p. 2) System Account Number 1 (p. 2) System Account Number 2 (p. 2) Evacuation Message Count (p. 38) 4 messages 1710 Phone Line 1 Dialing Prefix (p. 24) None Phone Line 2 Dialing Prefix (p. 24) None Dealer Access Code (p. 24) None Downloader Access Code (p. 24) Downloader Account Number (p. 42) Latitude Adjustment (p. 42) 0 degrees Time Fire Alarm is Silenced (p. 38) 30 sec Output Delay Time (p. 34) 30 sec Activation Interval One-Shot Times (p. 34) A 4 sec, B 30 sec, C 180 sec, D 900 sec Zone Delay Time (p. 33) 10 sec Downloader Callback (p. 39) Off AC Frequency (p. 42) 60 Hz Printer Supports Epson ESC/P Protocol (p. 41) On 1712 Partition/Area Text Speech (p. 40) On Unsilence Alarm (p. 38) Off Areas (p. 16) Off Annunciate Earliest Fire Alarm (p. 38) Off Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default 1, 2 Setting A, B, C, D 7

78 Appendix A: System Configuration Worksheets Item Number Reporting Number Enable (p. 2) Off Phone Numbers (p. 26) None Number of Attempts (p. 26) Communication Format (p. 26) 0 (Contact ID) Report Panic Special (p. 26) Off Pager Phone Number Enable (p. 26) Off Pager Phone Number (p. 26) None Number of Attempts (p. 27) Communication Format (p. 27) 1 (TAP at 1200 bps PSK) Communication Character Format (p. 27) 1 (7/E/1) Pager System Reports (p. 27) Off Partition/Area 1 Pager Reports (p. 27) Off Partition/Area 2 Pager Reports (p. 27) Off Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default Setting 19001, 20001, 21001, 22001, 23001, , 20002, 21002, 22002, 23002, , 20003, 21003, 22003, 23003, , 20004, 21004, 22004, 23004, , 2000, 2100, 2200, 2300, , 26001, 27001, 28001, 29001, 30001, 31001, 32001, 33001, 34001, 3001, 36001, 37001, 38001, 39001, , 26002, 27002, 28002, 29002, 30002, 31002, 32002, 33002, 34002, 3002, 36002, 37002, 38002, 39002, , 26003, 27003, 28003, 29003, 30003, 31003, 32003, 33003, 34003, 3003, 36003, 37003, 38003, 39003, , 26004, 27004, 28004, 29004, 30004, 31004, 32004, 33004, 34004, 3004, 36004, 37004, 38004, 39004, , 2600, 2700, 2800, 2900, 3000, 3100, 3200, 3300, 3400, 300, 3600, 3700, 3800, 3900, , 26006, 27006, 28006, 29006, 30006, 31006, 32006, 33006, 34006, 3006, 36006, 37006, 38006, 39006, , 26007, 27007, 28007, 29007, 30007, 31007, 32007, 33007, 34007, 3007, 36007, 37007, 38007, 39007, , 26008, 27008, 28008, 29008, 30008, 31008, 32008, 33008, 34008, 3008, 36008, 37008, 38008, 39008,

79 Appendix A: System Configuration Worksheets Item Number Partition/Area 3 Pager Reports (p. 27) Off Partition/Area 4 Pager Reports (p. 27) Off Partition/Area Pager Reports (p. 27) Off Partition/Area 6 Pager Reports (p. 27) Off Partition/Area 7 Pager Reports (p. 27) Off Partition/Area 8 Pager Reports (p. 27) Off Pager PIN (p. 27) None Pager Message Length (p. 27) 120 Characters Add Zones (p. 31) Delete Zones (p. 32) List Zones (p. 33) Zone Attributes (Edit Zones) (p. 33) 4700 Test Buddies (p. 33) List Buddies (p. 33) Add (Learn) Bus Devices (p. 34) Delete/Change Bus Device ID (p. 3) List Bus Devices (p. 3) Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default Setting 2009, 26009, 27009, 28009, 29009, 30009, 31009, 32009, 33009, 34009, 3009, 36009, 37009, 38009, 39009, , 26010, 27010, 28010, 29010, 30010, 31010, 32010, 33010, 34010, 3010, 36010, 37010, 38010, 39010, , 26011, 27011, 28011, 29011, 30011, 31011, 32011, 33011, 34011, 3011, 36011, 37011, 38011, 39011, , 26012, 27012, 28012, 29012, 30012, 31212, 32012, 33012, 34012, 3012, 36012, 37012, 38012, 39012, , 26013, 27013, 28013, 29013, 30013, 31013, 32013, 33013, 34013, 30113, 36013, 37013, 38013, 39013, , 26014, 27014, 28014, 29014, 30014, 31014, 32014, 33014, 34014, 3014, 36014, 37014, 38014, 39014, , 2601, 2701, 2801, 2901, 3001, 3101, 3201, 3301, 3401, 301, 3601, 3701, 3801, 3901, , 26016, 27016, 28016, 29016, 30016, 31016, 32016, 33016, 34016, 3016, 36016, 37016, 38016, 39016,

80 Appendix A: System Configuration Worksheets Item Number Bus Device Partition/Area (p. 3) 4800 Change Transmit Bus ID (p. 3) List Bus Device Text (p. 3) Replace/Delete Bus Device ID (p. 36) Program LED Module (p. 36) Delete/Replace LED Module (p. 36) Zone Text (p. 32) Bus Device Text (p. 3) Menu Output Text (p. 37) Partition/Area Text (p. 17) 4900 Keypad Idle Text (p. 36) 0001 Reset Panel (p. 42) 0002 Clear Memory (p. 1) 0003 Software/Hardware Version (p. 42) 0004 Clear History Buffer (p. 42) 000 Output Configuration (p. 37) Set Holiday Lists (p. 43) 0010 Set Event Configuration and Alarm Masks (p. 43) 0012 Print Zone & Device Information (p. 43) 0013 Access Code Length (p. 24) Delete Primary/Secondary SnapCard (p. 44) 0016 Print History Buffer (p. 44) Table A14: Item Numbers Index and Record (Continued) Setting Reference and Default Setting 78

81 Appendix B: Reference Tables Appendix B: Reference Tables This appendix contains tables for selecting zone type numbers, system features, X-10 Module house, unit codes and responses, SuperBus device unique ID numbers, and text No. Name Application 00 Fixed Panic 01 Portable Panic 02 Fixed Panic 03 Portable Panic 04 Fixed Auxiliary 0 Fixed Auxiliary Portable Auxiliary Portable Auxiliary 08 Special Intrusion 09 Special Intrusion 10 Entry/Exit Delay 11 Entry/Exit Delay 12 Entry/Exit Delay 24-hour audible fixed emergency buttons. 24-hour audible portable emergency buttons. 24-hour silent fixed emergency buttons. 24-hour silent portable emergency buttons. 24-hour auxiliary sensor, such as Pendant Panic or holdup button. 24-hour auxiliary emergency buttons. Siren shut-off confirms CS alarm report. 24-hour portable auxiliary alert buttons. 24-hour portable auxiliary button. Siren shut-off confirms CS alarm report. Special belongings, such as gun cabinets and wall safes. Special belongings, such as gun cabinets and wall safes. Entry and exit doors that require a standard delay time. Garage doors and entrances that require an extended delay time. * Driveway gates and entrances that require a twice extended delay time. * Table B1: Zone Type Characteristics Active Level 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, descriptor numbers. Table notes (if any) appear at the bottom of the last page of the table. Fire zone types are always active. Alarm/Siren Delay Supervisory Restoral CS Alarm Report CS Cancel Report Bypassable Police/Police Instant Police/Police Instant Police/Silent Instant Police/Silent Instant Aux./ Aux. Instant Aux./ Aux. Instant Aux./ Aux. Instant Aux./ Aux. Instant Police/Police Instant Police/Police Standard 2, 3, 4, Police/Police Standard 2, 3, 4, Police/Police Extended 2, 3, 4, Police/Police Twice Extended Chime 13 Instant Perimeter Exterior doors and windows. 2, 3, 4, Police/Police Instant 14 Instant Interior Interior doors. 2, 3, 4, Police/Police Follower 1 Instant Interior Interior PIR motion sensors. * 2, 3, 4, Police/Police Follower 16 Instant Interior Interior doors. 3, 4, Police/Police Follower 17 Instant Interior PIR motion sensors. * 3, 4, Police/Police Follower 18 Cross Zone Instant Interior 19 Delayed Interior PIR motion sensors subject to false alarms. * Interior doors that initiate a delay before going into alarm.* 3, 4, Police/Police Follower 3, 4, Police/Police Standard Resets Activity Timer 79

82 Appendix B: Reference Tables 20 Delayed Interior Fire Local Instant Interior Local Delayed Interior Local Instant Auxiliary Local Instant Auxiliary Local Special Chime 27 Custom Output 28 Custom Output 29 Auxiliary Auxiliary. 30 (A) Report Police 30 (B) Local Auxiliary 32 Custom Output 36 (A) Report Police 36 (B) Local Auxiliary 0 1 No. Name Application Local Instant Interior Local Delayed Interior 2 Local Indicator Table B1: Zone Type Characteristics (Continued) PIR motion sensors that initiate a delay before going into alarm. * 24-hour local alarm zone protecting anything that opens and closes. Same as type 21, plus activation initiates a delay before going into alarm. 24-hour local alarm zone protecting anything that opens and closes. 24-hour local alarm zone protecting anything that opens and closes. Sirens shut off at restoral. * Notify the user when a door is opened. Sounds emit from a local annunciator. * 24-hour audible fire emergency buttons, rate-of-rise heat, and smoke sensors. Output, lamp control, or other customer feature. Output, PIR motion sensor, sound sensor, or pressure mat. 24-hour audible police alarm in levels 2 and hour audible auxiliary alarm in level 1. Siren shut off at restoral. Output, PIR motion sensor, sound sensor, or pressure mat. 24-hour audible police alarm in levels 2 and hour audible auxiliary alarm in level hour local alarm zone protecting anything that opens and closes. 24-hour local alarm zone protecting anything that opens and closes. 24-hour local auxiliary alarm zone protecting anything that opens and closes. No voice. Sirens shut off at restoral. * Active Level 3, 4, Police/Police Standard 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, Police/Police Instant Police/Police Standard Aux./Aux. Instant Aux./Aux. Instant Special Chime Instant Fire/Fire Instant Silent Instant Silent Instant Aux. Instant 2, 3, 4, Police/Police Instant 1 Aux./Aux. Instant 1, 2, 3, 4, Silent Instant 2, 3, 4, Police/Police Instant 1 Aux./Aux. Instant 2, 3, 4, Police/Police Instant 2, 3, 4, Police/Police Standard 1, 2, 3, 4, Alarm/Siren Delay Supervisory Restoral CS Alarm Report CS Cancel Report Bypassable Aux./Aux. Instant Chime Resets Activity Timer 80

83 Appendix B: Reference Tables 3 Local Indicator 4 Fixed Medical Fixed Medical 6 Portable Medical 7 Portable Medical 8 Suspicion 9 Fire Keyswitch 60 (A) Police 60 (B) Fire 61 Local Indicator/ Delay Perimeter 62 Fire Panic Fire Panic Equipment Tamper Equipment Tamper 6 Siren Tamper 24-hour local indicator zone protecting anything that opens and closes. Chime only. 24-hour audible fixed medical emergency buttons. 24-hour audible fixed medical emergency buttons. Sirens shut off when reported. 24-hour audible portable medical emergency buttons. 24-hour audible portable medical emergency buttons. Sirens shut off when reported. If not canceled within 1- min., alarm may optionally be generated. A second trip within 1- min. will cause an alarm. Keyswitch used for enabling fire type touchpad. 24-hour audible police emergency buttons. 24-hour audible fire emergency buttons 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, None Instant Medical/ Medical Medical/ Medical Medical/ Medical Medical/ Medical Suspicion/ Silent Instant Instant Instant Instant Instant Silent Instant 3, Police/Police Instant 1, 2, 4, Fire/Fire Instant Local beeps only in Level -1. 2, 3, 4, Police/Police Standard 24-hour audible security system panel tamper alarm. 24-hour silent security system panel tamper alarm. 24-hour audible siren tamper alarm. 66 Siren Tamper 24-hour silent siren tamper alarm. 67 Unused Carbon Monoxide Touchpad disable keyswitch 70 Warning 71 No. Name Application On/Off Keyswitch Table B1: Zone Type Characteristics (Continued) Carbon Monoxide gas detectors. : For residential use only. Keyswitch for disabling touchpad. Trip plays programmable evacuation message. Trip causes arm. Restoral causes a disarm. Active Level 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, Alarm/Siren Fire/Fire Instant Equipment Tamper/ Police Instant Equipment Tamper/None Instant Siren Tamper/ Police Instant Siren Tamper/None Instant Carbon Monoxide/Medical Delay Supervisory Restoral CS Alarm Report CS Cancel Report Instant Bypassable None/None Instant Chime None/None Instant Resets Activity Timer None/None Instant 81

84 Appendix B: Reference Tables 72 Momentary Keyswitch 73 Fixed Holdup 74 Portable Holdup First trip arms, second trip disarms. 24-hour silent fixed holdup emergency button alarm. 24-hour silent portable holdup emergency button alarm. 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, None/None Instant Holdup/None Instant Holdup/None Instant 7 Night Interior Disarmed in night level. 3, Police/Police Follower 76 Night Interior Disarmed in night level. 3, Police/Police Follower Smoke Cross Zone Night Delayed Interior Night Delayed Interior Night Delayed Interior Disarmed in night level. 3, Police/Police Follower Disarmed in night level. 3, Police/Police Standard Disarmed in night level. 3, Police/Police Standard 24-hour audible smoke/fire alarm. 81 Heat 24-hour audible heat/fire alarm. 82 Water Flow 83 Unused. 84 Enhanced Buddy 24-hour audible sprinkler/fire alarm. Special enhanced buddy system function. 8 Repeater Wireless signal repeaters Fixed Wireless Touchpad Portable Wireless Touchpad 88 Unused. 89 Unused. Fixed (wall-mount) wireless touchpads Portable (hand-held) wireless touchpads : For residential use only. 1, 2, 3, 4,, 6 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, 90 Pump Active Fire pump is active. 1, 2, 3, 4, 91 Pump Failure Fire pump has failed. 1, 2, 3, 4, 92 No. Name Application Gate Valve Closed Table B1: Zone Type Characteristics (Continued) Fire gate valve has been closed. 1, 2, 3, 4, 93 CO2 Pressure CO2 pressure is low. 1, 2, 3, 4, 94 Liquid Pressure Liquid pressure is low. 1, 2, 3, 4, 9 Liquid Level Liquid level is low. 1, 2, 3, 4, Active Level Alarm/Siren Smoke/Fire Instant Heat/Fire Instant Sprinkler/Fire Instant Buddy/None Instant None/None Instant None/None Instant None/None Delay Instant Supervisory Restoral Fire/Fire Instant Aux./Aux. Instant Aux./Aux. Instant Aux./Aux. Instant Aux./Aux. Instant Aux./Aux. Instant CS Alarm Report CS Cancel Report Bypassable Chime Resets Activity Timer 82

85 Appendix B: Reference Tables Table B1: Zone Type Characteristics (Continued) No. Name Application Active Level Alarm/Siren Delay Supervisory Restoral CS Alarm Report CS Cancel Report Bypassable Chime Resets Activity Timer 96 Fire Supervisory A fire supervisory trouble has 1, 2, 3, 4, been detected. Aux./Aux. Instant : Check marks ( ) represent characteristics present in a type. * This type is not certified as a primary protection circuit for UL-listed systems and is for supplementary use only. Sounds instant police siren if two or more sensors are tripped within 4 minutes; otherwise sensors are followers to delayed sensors. If central station Alarm Verification feature is on, type 18 functions like type 17. This type has not been investigated by UL. Zone trip causes trouble, restoral causes trouble restoral. Activity Levels as Follows: \ Level # Name Description Attributes Level 1 Level 2 Level 3 Level 4 OFF PERIMETER/ HOME FULL/AWAY NIGHT The partition/area is disarmed. Only 24-hour sensors cause an alarm in the OFF level. Cancelling alarms or entry delay automatically disarms to OFF. The user is on-site and only requires perimeter protection. In addition to 24- hour sensors, perimeter sensors such as those protecting exterior doors and windows cause an alarm in the HOME/PERIMETER level. The user is away and requires complete protection. 24-hour sensors, perimeter sensors, and interior sensors cause an alarm in the AWAY/FULL level. The user is on-site and perimeter and 24-hour sensors are active. Since users are not moving around, Interior sensors except those in night groups are also active. - Open - Entry, but no exit delay - Cannot be disabled - Closed - Entry and exit delay - Can be disabled Same as Level 2. Same as Level 2. Level SILENT Same as Level 3, but police intrusion alarms are silent. Same as Level 2. 83

86 Appendix B: Reference Tables No. Text Descriptor THOUSAND_ 031 ONE_ 032 0_ 033 1_ 034 2_ 03 3_ 036 4_ 037 _ 038 6_ 039 7_ 040 8_ 041 9_ _ Table B2: Three-Digit Text Descriptors No. Text Descriptor _ _ 76 24_ 04 Dash 046 Cursor 047 Space And 12 ms Pause 048 Space 049 Blink Next Token 00 Break Line (Return) 01 Period (Dot) 02 Apostrophe 03 AM_ 04 PM_ 0 12 ms Pause ms Pause ms Pause ms Beep ms Beep ms Beep ms Low Beep ms Low Beep ms Low Beep 064 Long Beep 06 Chime Ding 066 Chime Dong 067 A (display only) 068 A 069 A_ (short) 070 ABORT_ 071 ABORTED_ 072 ABOVE_ 766 AC_ (A.C.) 073 ACCEPT_ 074 ACCESS_ 07 ACKNOWLEDGE_ 076 ACKNOWLEDGMENT_ 077 ACTIVE_ 078 ACTIVITY_ 079 ADD_ 080 ADDED_ 081 ADDRESS_ 767 ADDRESSABLE_ No. Text Descriptor 082 ADVENT_ 083 AGAIN_ 084 AGENT_ 08 AIR_ 086 ALARM_ 087 ALERT_ 088 ALL_ 089 ALLEY_ 090 AN_ 768 ANALOG_ 091 AND_ 092 ANNEX_ 093 ANNUNCIATOR_ 094 ANTENNA_ 09 APARTMENT_ 096 APPLIANCE_ 097 APRIL_ 098 ARE_ 099 AREA_ 100 ARM_ 101 ARMED_ 102 ARMING_ 103 ART_ 104 AS_ 10 ASSEMBLY_ 106 ATTIC_ 107 ATTRIBUTE_ 108 AUDIO_ 109 AUGUST_ 110 AUTHORITY_ 111 AUTO_ 112 AUTO ARMING_ 113 AUTOMATIC_ 114 AUTOMATION_ 11 AUXILIARY_ 116 AWAY_ 117 B (display only) 118 B 119 BABY S_ 120 BACK_ 121 BACKUP_ 122 BAD_ 84

87 Appendix B: Reference Tables No. Text Descriptor 123 BADGE_ 124 BALCONY_ 12 BAR_ 126 BARN_ 127 BASEMENT_ 128 BATH_ 129 BATTERY_ 130 BAY_ 131 BEDROOM_ 769 BELL_ 132 BLACK_ 133 BLOWER_ 134 BLUE_ 13 BOAT_ 136 BOILER_ 137 BOTTOM_ 770 BOX_ 138 BREAK_ 139 BREAKER_ 140 BREATHING_ 141 BREEZEWAY_ 142 BRIGHTEN_ 143 BROWN_ 144 BUDDY_ 14 BUFFER_ 146 BUILDING_ 147 BUS_ 148 BUSINESS_ 149 BUSY_ 10 BYPASS_ 11 BYPASSED_ 12 C (display only) 13 C 14 CABIN_ 1 CABINET_ 16 CAGE_ 771 CALL_ 17 CALLER ID_ 18 CAMERA_ 19 CANCEL_ 160 CANCELED_ 161 CAR_ 162 CARBON MONOXIDE_ No. Text Descriptor 163 CASH_ 164 CCTV_ 16 CEILING_ 166 CELLAR_ 167 CELLULAR_ 168 CENTER_ 169 CENTRAL_ 170 CHANGE_ 171 CHANGED_ 172 CHECK IN_ 173 CHECKSUM_ 174 CHIME_ 772 CIRCUIT_ 17 CLASS_ 176 CLEAR_ 177 CLEARED_ 178 CLOSE_ 179 CLOSED_ 180 CLOSET_ 181 CLOSING_ 182 CO_ 183 CO2_ 184 COAT_ 18 CODE_ 186 CODE S_ 187 CODES_ 188 COLLECTION_ 189 Colon 190 COMMON_ 191 COMMUNICATION_ 192 COMMUNICATOR_ 193 COMPLETE_ 194 COMPUTER_ 19 CONFERENCE_ 196 CONFIGURATION_ 197 CONSERVATORY_ 198 CONTACT_ 199 CONTINUE_ 200 CONTROL_ 201 COOLER_ 202 CORRIDOR_ 203 COTTAGE_ 204 COUNT_ No. Text Descriptor 20 COUNTER_ 206 CPU_ 207 CRITICAL_ 208 CUSTOM_ 209 D (display only) 210 D 211 DAMPER_ 212 DATA_ 213 DAUGHTER S_ 214 DAY_ 21 DAYLIGHT_ 216 DAYS_ 773 DEALER_ 217 DECEMBER_ 218 DECK_ 219 DEGREES_ 220 DELAY_ 221 DELETE_ 222 DELETED_ 223 DEN_ 224 DESCRIPTORS_ 22 DESK_ 226 DETECTOR_ 227 DEVICE_ 228 DEVICES_ 229 DIAL_ 230 DIFFERENT_ 231 DIM_ 232 DINING_ 233 DIRECT_ 234 DISABLE_ 23 DISABLED_ 236 DISARM_ 237 DISARMED_ 774 DISPLAY_ 238 DO_ 77 DOCK_ 239 DOES_ (long) 240 DOES_ (short) 241 DOOR_ 242 DOWN_ 243 DOWNLOAD_ 244 DOWNSTAIRS_ 8

88 Appendix B: Reference Tables No. Text Descriptor 24 DRILL_ 246 DRIVEWAY_ 247 DRUG_ 248 DUAL_ 249 DUCT_ 20 DURESS_ 21 E (display only) 22 E 23 EARLY_ 24 EAST_ 2 EIGHTH_ 776 ELECTRICAL_ 26 ELEVATOR_ 27 ELEVENTH_ 28 EMERGENCY_ 29 EMPLOYEE_ 260 ENABLE_ 261 ENERGY SAVER_ 262 ENERGY SAVERS_ 263 ENTER_ 264 ENTERED_ 26 ENTRANCE_ 266 ENTRY_ 267 ENVIRONMENTAL_ 268 EQUIPMENT_ 269 ERROR_ 270 EVACUATION_ 271 EVENT_ 272 EXECUTIVE_ 273 EXERCISE_ 274 EXIST_ 27 EXISTS_ 276 EXIT_ 277 EXPLOSIVE_ 278 EXTEND_ 279 EXTENDED_ 280 EXTENSION_ 281 EXTERIOR_ 282 EXTINGUISHER_ 283 F (display only) 284 F 28 FACTORY_ 286 FAILED_ No. Text Descriptor 287 FAILURE_ 288 FAMILY_ 289 FAN_ 290 FATHER S_ 291 FAULT_ 292 FEATURE_ 293 FEATURES_ 294 FEBRUARY_ 29 FENCE_ 296 FIFTH_ 297 FILE_ 298 FIRE_ 299 FIRST_ 777 FLAME_ 300 FLASH_ 301 FLOOD_ 302 FLOOR_ 303 FLOW_ 304 FOR_ 30 FORCE_ 306 FORMAT_ 307 FOURTH_ 308 FOYER_ 309 FREEZE_ 310 FREEZER_ 311 FRIDAY_ 312 FROM_ 313 FRONT_ 314 FULL_ 31 FURNACE_ 316 G (display only) 317 G 318 GALLERY_ 319 GAME_ 320 GARAGE_ 321 GARDEN_ 322 GAS_ 323 GATE_ 324 GENERATOR_ 778 GENERAL_ 32 GLASS_ 326 GLOBAL_ 327 GOLD_ No. Text Descriptor 328 GOOD_ 329 GOODBYE_ 330 GRAY_ 331 GREEN_ 332 GROUND_ 333 GROUP_ 334 GUARD_ 33 GUEST_ 336 GUN_ 337 H (display only) 338 H 339 HALL_ 340 HALLWAY_ 341 HARDWIRE_ 342 HEAD_ 343 HEAT_ 344 HEATER_ 34 HEATING_ 346 HELLO_ 347 HELP_ 348 HIGH_ 349 HISTORY_ 30 HOLDUP_ 31 HOLIDAY_ 32 HOME_ 779 HORN_ 33 HOT TUB_ 34 HOUSE_ 3 I (display only) 36 I 37 ID_ 38 IN_ 780 INDICATING_ 39 INDIRECT_ 360 INDOOR_ 361 INFORMATION_ 362 INFRARED_ 363 INHIBIT_ 781 INITIATING_ 364 IN PROGRESS_ 36 INPUT_ 366 IN SERVICE_ 367 INSIDE_ 86

89 Appendix B: Reference Tables No. Text Descriptor 368 INSTANT_ 369 INTEGRATION_ 370 INTERCOM_ 371 INTERIOR_ 372 INTRUSION_ 373 INVALID_ 374 IS_ 37 ITEM_ 376 J (display only) 377 J 378 JACUZZI_ 379 JAM_ 380 JANITOR_ 381 JANUARY_ 382 JEWELRY_ 383 JOFFRE_ 384 JULY_ 38 JUNE_ 386 K (display only) 387 K 782 KEY_ 388 KEYFOB_ 389 KEYSTROKE_ 390 KEYSWITCH_ 391 KITCHEN_ 392 L (display only) 393 L 394 LADIES _ 39 LAKE_ 396 LATCHKEY_ 397 LATE_ 398 LAUNDRY_ 783 LED_ (L.E.D.) 399 LEARN_ 400 LEFT_ 401 LENGTH_ 402 LEVEL_ 403 LIBRARY_ 404 LIGHT_ 40 LIGHTING_ 406 LIGHTS_ 407 LIMIT_ 408 LIMITS_ No. Text Descriptor 409 LINE_ 410 LIQUID_ 411 LIQUOR_ 412 LIST_ 413 LISTEN_ 414 LIVING_ 41 LOBBY_ 416 LOCAL_ 417 LOCKOUT_ 418 LOG_ 419 LONG_ 420 LOOP_ 421 LOT_ 422 LOUNGE_ 423 LOW_ 424 LOWER_ 42 LTIME_ 426 M (display only) 427 M 428 MACHINE_ 429 MAID S_ 430 MAILBOX_ 431 MAIN_ 784 MAINTENANCE_ 432 MALL_ 433 MANAGER S_ 78 MANUAL_ 434 MANUFACTURING_ 43 MARCH_ 786 MASK_ 436 MASTER_ 437 MAT_ 438 MAY_ 439 MECHANICAL_ 440 MEDIA_ 441 MEDICAL_ 442 MEDICINE_ 443 MEMORY_ 444 MEN S_ 44 MENU_ 446 MESSAGE_ 447 MICROPHONE_ 448 MICROWAVE_ No. Text Descriptor 449 MIDNIGHT_ 40 MINUTES_ 41 MODE_ 42 MODIFIER_ 43 MODIFY_ 44 MODULE_ 4 MONDAY_ 46 MONEY_ 47 MOTHER S_ 48 MOTION_ 49 MOTOR_ 460 N (display only) 461 N 787 NAC_ ( knack ) 462 NEGATIVE_ 463 NEW_ 464 NIGHT_ 46 NINTH_ 466 NO_ 788 NON_ 467 NON-REPORTING_ 468 NOON_ 469 NORMAL_ 470 NORTH_ 471 NOT_ 472 NOVA ALERT_ 473 NOVEMBER_ 474 NOW_ 47 NUMBER_ 476 NUMBERS_ 477 NURSERY_ 478 O (display only) 479 O 480 OBSCURITY_ 481 O CLOCK_ 482 OCTOBER_ 483 OF_ 484 OFF_ 48 OFFICE_ (spoken as OH) 487 OK_ 488 ON_ 489 OPEN_ 87

90 Appendix B: Reference Tables No. Text Descriptor 490 OPENING_ 491 OPTION_ 492 OR_ 493 ORANGE_ 494 OUT_ 49 OUTDOOR_ 496 OUTPUT_ 497 OVER_ 498 P (display only) 499 P 00 PAGER_ 01 PAINTING_ 02 PANEL_ 03 PANIC_ 04 PANTRY_ 0 PARENTS _ 06 PARKING_ 07 PARTITION_ 08 PATH_ 09 PATIO_ 10 PERIMETER_ 11 PERIOD_ 12 PERMANENT_ 13 PHONE_ 14 PHOTO_ 1 PLACE_ 16 PLANT_ 17 PLEASE_ 18 POLICE_ 19 POOL_ 789 PORCH 20 POSITIVE_ 21 POUND_ 22 #_ (spoken as Pound) 23 # (spoken as Pound) 24 POWER_ 2 PREARM_ 26 PRESS_ 27 PRESS_ (on new line) 28 PRESSURE_ 29 PRIMARY_ 30 PRINTER_ 31 PROGRAM_ No. Text Descriptor 32 PROGRAMMING_ 33 PROTEST_ 34 PULL STATION_ 3 PUMP_ 36 PURPLE_ 37 Q (display only) 38 Q 39 QUAD_ 40 QUIET_ 41 QUIT_ 42 R (display only) 43 R 44 RADIO_ 4 RAMP_ 46 RANGE_ 47 READY_ 48 REAR_ 790 RECALL 49 RECEIVER_ 0 RECEIVING_ 1 RECEPTION_ 2 RECONNECT_ 3 RED_ 4 REDIRECT_ RELAY_ 6 RELEASE_ 7 REMOTE_ 8 REMOVE_ 9 REMOVED_ 60 REPEATER_ 61 REPORT_ 791 REQUEST 62 RESET_ 63 RESTORAL_ 64 RESTORED_ 6 RETURN_ 66 REVIEW_ 67 RF_ 68 RIGHT_ 69 RING_ 70 ROOF_ 71 ROOM_ 72 S (display only) No. Text Descriptor 73 S 74 SAFE_ 7 SATURDAY_ 76 SAUNA_ 77 SCHEDULE_ 78 SCHEDULES_ 79 SCHOOL_ 80 SCREEN_ 81 SCRIPT_ 82 SCRIPTS_ 83 2ND_ 84 SECOND_ 792 SECONDARY 8 SECONDS_ 86 SECTION_ 87 SECTOR_ 88 SECURE_ 89 SECURITY_ 90 SELECTION_ 793 SENSITIVITY 91 SENSOR_ 92 SENSORS_ 93 SEPTEMBER_ 94 SERVANT_ 9 SERVICE_ 96 SET_ 97 SETPOINT_ 98 SETUP_ 99 SEVENTH_ 600 SHACK_ 601 SHARED_ 602 SHED_ 603 SHEEP_ 604 SHIPPING_ 60 SHOCK_ 606 SHOP_ 607 SHORT_ 794 SHUNT 79 SHUTDOWN 796 SIGNALING 608 SHUT OFF_ 609 SIDE_ 610 SIGNAL_ 88

91 Appendix B: Reference Tables No. Text Descriptor 611 SILENCE_ 612 SILENT_ 613 SILVER_ 614 SIREN_ 61 SITE_ 616 SIXTH_ 617 SKYLIGHT_ 618 SLIDING_ 619 SMOKE_ 797 SNAPCARD 620 SON S_ 621 SOUND_ 622 SOUTH_ 623 SPEAKER_ 624 SPECIAL_ 798 SPECIFIC 62 SPRINKLER_ 626 STAIR_ 627 STAIRS_ 628 STANDARD_ 629 *_ (spoken as Star) 630 Flashing * -- do not use 631 * (spoken as Star) 632 START_ 633 STARTING_ 634 STATION_ 63 STATUS_ 636 STAY_ 637 STIME_ 638 STOP_ 639 STORAGE_ 640 STORE_ 641 STORY_ 642 STRIKE_ 643 STRIP_ 644 STROBE_ 64 STUDY_ 646 SUMP_ 647 SUPERBUS_ 648 SUPERVISORY_ 649 SUSPICION_ 60 SUNDAY_ 61 SWIMMING_ No. Text Descriptor 62 SWINGER_ 63 SWITCH_ 64 SYSTEM_ 6 T (display only) 66 T 67 TAMPER_ 68 TAMPERED_ 69 TANK_ 660 TAPE_ 661 TELCO_ 662 TELLER_ 663 TEMPERATURE_ 664 TEMPORARY_ 66 TENTH_ 666 TEST_ 667 TESTED_ 668 TEXT_ 669 THE_ (short) 670 THEATER_ 671 THE_ (spoken as short Thee) 672 THEN_ 673 THERMOSTAT_ 674 THIRD_ 67 Dash (spoken as Through) 676 Dash_ (spoken as Through) 677 THURSDAY_ 678 TIME_ 679 TIMED_ 680 TIMER_ 681 TIMEOUT_ 682 TO_ 683 TONE_ 684 TOOL_ 68 TOOLBOX_ 686 TOP_ 687 TOUCHPAD_ 688 TRAILER_ 689 TRANSCEIVER_ 690 TRANSMIT_ 691 TRAP_ 692 TRIES_ 693 TRIP_ 694 TROUBLE_ No. Text Descriptor 69 TRUCK_ 696 TUESDAY_ 697 TURN_ 698 TWELFTH_ 699 TWICE_ 700 TYPE_ 701 U (display only) 702 U 703 A_ (spoken as Uh) 704 UNBYPASS_ 70 UNDER_ 706 UNIT_ 707 UP_ 799 UPLOAD 708 UPSTAIRS_ 709 USE_ 710 USED_ 711 USER_ 712 UserTokens -- do not use 713 USES_ 714 UTILITY_ 71 V (display only) 716 V 717 VALID_ 718 VALUE_ 719 VALVE_ 720 VAULT_ 800 VERIFICATION 721 VERSION_ 722 VESTIBULE_ 723 VIBRATION_ 724 VIDEO_ 72 VIEW_ 726 VIOLATION_ 727 VOICE_ 728 EVAC MESSAGE EVAC MESSAGE EVAC MESSAGE EVAC MESSAGE EVAC MESSAGE 733 VOLTS_ 734 VOLUME_ 73 W (display only) 89

92 Appendix B: Reference Tables No. Text Descriptor 736 W 737 WAIT_ 738 WALL_ 739 WAREHOUSE_ 740 WARNING_ 741 WASH_ 742 WASHROOM_ 743 WATER_ 801 WEATHER 744 WEDNESDAY_ 74 WEEK_ No. Text Descriptor 746 WEEKLY_ 802 WELL 747 WEST_ 748 WHITE_ 749 WINDOW_ 70 WINE_ 71 WING_ 72 WORKSHOP_ 73 X (display only) 74 X 7 Y (display only) No. Text Descriptor 76 Y 77 YARD_ 78 YELLOW_ 79 YES_ 760 YOUR_ 761 Z (display only) 762 Z 763 ZONE_ 764 ZONES_ Table B3: Two-Digit Display Descriptors No. Token Text No. Token Text M N O P Q 0 34 R S T U V 10 (undefined) 39 W 11 (undefined) 40 X 12 # (pound) 41 Y 13 : (colon) 42 Z 14 / (slash) 43 _ (space) 1? (question mrk) 44 (apostrophe) 16. (period) 4 -- (dash) 17 A 46 (underline) 18 B 47 * (star) 19 C 48 (time) 20 D 49 (date) 21 E 0 (day and date) 22 F 1 _(pseudo space) 23 G 2 (return) 24 H 2 I 26 J 27 K 28 L 3 * (Flashing star) Trouble Indicator Table B4: Panel House Code Defaults/Settings for 4 Partition Panels Partition/ Area 1 HC1 = 1 HC2 = 2 HC1 = 2 HC2 = 6 3 HC1 = 3 HC2 = 7 4 HC1 = 4 HC2 = 8 Panel House Code Defaults (HC1, HC2) A E B F X-10 House Dial C G D H House Code X-10 House Dial Table B: Panel House Code Defaults/Settings for 8 Partition Panels Panel House Code X-10 Partition/ X-10 House House Defaults House Area Dial Code (HC1, HC2) Dial 1 HC1 = 1 HC2 = 9 2 HC1 = 2 HC2 = 10 3 HC1 = 3 HC2 = 11 4 HC1 = 4 HC2 = 12 HC1 = HC2 = 13 6 HC1 = 6 HC2 = 14 7 HC1 =7 HC2 = 1 8 HC1 = 8 HC2 = 16 A I B J C K D L E M F N G O H P 90

93 Appendix B: Reference Tables Table B6: X-10 Module Operation Condition Lamp Module Unit No. 1 Lamp Module Unit Nos Appliance/Universal Module Unit Nos On entry delay On for minutes Unchanged Unchanged On Fire Alarm* On On Unchanged On Police Alarm* On On Unchanged On Auxiliary Alarm* On On Unchanged Lights On On On Unchanged Lights Off Off Off Off * Fire alarms have priority over both police and auxiliary alarms. Police alarms have priority over auxiliary alarms. 91

94 Appendix B: Reference Tables Table B7: X-10 and Non-X-10 Light/Device Numbers by Partition X-10 Unit Partition 1 Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number X-10 Unit Partition 2 Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number 92

95 Appendix B: Reference Tables X-10 Unit Partition 3 Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number X-10 Unit Partition 4 Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number 93

96 Appendix B: Reference Tables X-10 Unit Partition Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number X-10 Unit Partition 6 Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number 94

97 Appendix B: Reference Tables X-10 Unit Partition 7 Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number X-10 Unit Partition 8 Dial Setting House Code 1 Light/Device Number House Code Non-X Menu Output Number 9

98 Appendix B: Reference Tables Contact ID Codes and Event Types Use Table B8 for determining event types and CID codes. Items in grey are not supported. Table B8: Contact ID Codes Description Specific Type Contact ID Code Associated Zone Type Alarms (General Types 1 Alarm, 2 Alarm Cancel, 3 Alarm Restoral) : All alarm cancels are reported as CID code 406 *Advent has a defined level that reports silent burglary (CID 146). This will be used in place of the defined event code at the appropriate level. Unspecified Fire , 90 Fire Panic (B), 62, Touchpad Panics Police , 9, 30*, 60(A), 61*, 64*, 7-79* Police Panic , 1, Touchpad Panics Medical , Touchpad Panics Medical Panic , Touchpad Panics Auxiliary Auxiliary Panic , Touchpad Panics Tamper *, 6*, 66*, 8, Any Zone No Activity Suspicion , 3, 8, 73, 74 Buddy Low Temperature Limit High Temperature Limit Keystroke Violation 1 14 Duress Exit Fault Explosive Gas , 67 Carbon Monoxide Environmental Latchkey Equipment Tamper Holdup , 3, 8, 73, 74 Sprinkler Heat Siren Tamper Table B8: Contact ID Codes (Continued) Description Specific Type Contact ID Code Associated Zone Type Smoke Repeater *, 6*, 66*, 8, Any Zone Fire Pump Activated , 90 Fire Pump Failure Fire Gate Valve Low CO2 Pressure Low Liquid Pressure Low Liquid Level Entry Exit Intrusion (Police) * Perimeter Intrusion (Police) * Interior Intrusion (Police) * Fire Supervisory Fire Trouble (General Types 4 Zone Trouble Fire, Zone Trouble Restoral Fire) Unspecified Hardwire Trouble Ground Fault Device Trouble RF Supervisory RF Low Battery 384 Tamper Suspected Sensor Failure Partial Obscurity RF Jam Zone AC Failure Zone Low Battery NAC Trouble Analog Zone Trouble Fire Supervisory Trouble Pump Failure Gate Valve Closed CO2 Pressure Liquid Pressure Liquid Level Non-Fire Trouble (General Types 6 Zone Trouble Non Fire, 7 Zone Trouble Restoral Non Fire) Unspecified Hardwire Trouble Ground Fault

99 Appendix B: Reference Tables Table B8: Contact ID Codes (Continued) Table B8: Contact ID Codes (Continued) Description Specific Type Contact ID Code Device Trouble RF Supervisory RF Low Battery 384 Tamper Suspected Sensor Failure Partial Obscurity RF Jam Zone AC Failure Zone Low Battery NAC Trouble Analog Zone Trouble Fire Supervisory Trouble Pump Failure Gate Valve Closed CO2 Pressure Liquid Pressure Liquid Level Bypass and Unbypass (General Types 8 Bypass, 9 Unbypass Direct 0 70 Indirect 1 70 Swinger 2 7 Inhibit 3 70 Opening (General Type 10 Opening) Normal Early 1 41 Late 2 42 Fail 3 43 Exception 4 40 Extension 40 Keyswitch/Keyfob Disarm Scheduled Disarm Remote Closing (General Type 11 Closing) Normal Early 1 41 Late 2 42 Fail 3 44 Exception 4 40 Associated Zone Type Description Specific Type Contact ID Code Associated Zone Type Extension 464 Keyswitch/Keyfob Disarm Scheduled Disarm Remote Partition/Area Configuration Change (General Type 12 Partition/Area Configuration Change) Access Code Added Access Code Deleted Access Code Changed Access Code Expired Code Authority Changed Authority Level Changed 306 Schedule Changed Arm/OC Schedule Changed Zone Added Zone Deleted Partition/Area Event (General Type 13 Partition/Area Event) Schedule On Schedule Off Latchkey On Latchkey Off Smoke Loop Reset Access Code Entered 462 Arming Level Change Alarm Reported Agent Release Agent Release Restoral Remote Access Keystroke Violation Manual Force Arm Auto Force Arm Force Arm Failed 14 4 Protest Start Protest End Partition/Area Test (General Type 14 Partition/Area Test) Manual Phone Test Auto Phone Test Off-Normal Auto Phone Test

100 Appendix B: Reference Tables Table B8: Contact ID Codes (Continued) Description Specific Type Contact ID Code Associated Zone Type Phone Test Passed Phone Test Failed User Zone Test Started 607 User Zone Test Ended User Zone Test Complete User Zone Test Incomplete User Zone Test Trip Installer Zone Test Started Installer Zone Test Ended Installer Zone Test Complete Installer Zone Test Incomplete Installer Zone Test Trip Fire Drill System Trouble (General Types 1 System Trouble, 16 System Trouble Restoral) Receiver Failure 0 3 Antenna Tamper 1 3 Main Low Battery SnapCard Low Battery Module Low Battery Main AC Power Failure 301 Snap Card AC Power Failure Module AC Power Failure Auxiliary Power Failure Shutdown Bus Low Power Mode Phone Line #1 Failure (will be reported to phone 2) Phone Line #2 Failure (will be reported to phone 1) Remote Phone Tamper Watchdog Reset RAM Failure Flash Error Printer Trouble History Buffer Full History Buffer Overflow Report Buffer Overflow Bus Device Failure Table B8: Contact ID Codes (Continued) Description Specific Type Contact ID Code Failure to Communicate Long Range Radio Trouble Module Tamper Unenrolled Module Audio Amplifier Trouble Analog Module Trouble Cell Module Trouble Buddy #1 Failure , 8 Buddy #2 Failure , 8 Buddy #3 Failure , 8 Buddy #4 Failure , 8 SnapCard Trouble Analog Loop Short Analog Loop Break Analog Head at Address Unenrolled Analog Head Duplicate Analog Head Analog Loop Initializing Microphone Switch Trouble Microphone Trouble Microphone Audio Trouble JTech Module Trouble Voice Siren Tamper Microburst Transmit Fault 4 33 Microburst Disabled Microburst Module Failure Microburst not in service Microburst Module Supervisory System Configuration Change (General Type 17 System Configuration Change) Program Mode Entry Program Mode Exit No Change Program Mode Exit With Change Download Started Download Ended No Change Download Ended With 412 Change Download Error Associated Zone Type 98

101 Appendix B: Reference Tables Table B8: Contact ID Codes (Continued) Description Specific Type Contact ID Code Download Denied Date/Time Changed 8 62 Expansion Module Added 9 31 Expansion Module Deleted Speech Tokens Changed Program Code Changed First Service -- Cold Reset Back in Service -- Warm Reset Installer Code Changed System Event (General Type 18 System Event) Callback Requested Output Activity Buddy Reception Buddy Transmit Request History Buffer Cleared Output On 300 Output Off System Test (General Type 19 System Test) Manual Phone Test Auto Phone Test Off-Normal Auto Phone Test Phone Test Passed Phone Test Failed Associated Zone Type Additional CID Reporting Table B9 shows additional CID reports. Table B9: Additional CID Reporting Type Number Range Example System Reports 00 System low battery would report as 000. Normal Zones Zone number 4 would report as 004. Bus Devices Device number 1 would report as 01. Touchpad Panic Zones 9 99 Touchpad fire panic would report as 99 Touchpad police panic would report as 98. Touchpad auxiliary panic would report as 97. Touchpad medical panic would report as 96. : Only if setting yy00 is on. User User number 2 would report as 62. Local Phone Reports 900 Local phone panic would report as 900. Remote Phone Reports 901 Remote phone, phone test would report as 901. Installer Code 999 Alarm cancelled with installer code would report as

102 Appendix B: Reference Tables LED Types LED Description Type 0 Disable all LED s (default) Table B10: LED Types and Behavior LED Data When the Green LED is On LED Type Behavior When the Yellow LED is On 1 Zone status type 1 Zone number Zone normal Zone in trouble or bypassed 2 Zone status type 2 Zone number Zone normal Zone open, in trouble, or bypassed 3 Zone status type 3 Zone number Zone normal Zone in trouble or bypassed 4 Programmable output status type 1 Output number Output off Output on When the RED LED is On Zone in alarm Zone in alarm Zone open (unrestored) Programmable output status type 2 Output number Output off Output on 6 Arming level Partition/Area Partition/Area disarmed Partition/Area armed 7 Alarm/Trouble status Partition/Area Partition/Area normal Partition/Area in trouble Partition/Area in alarm 8 System trouble No system trouble System trouble 9 Main AC trouble Main AC on Main AC off 10 SnapCard AC trouble SnapCard AC on SnapCard AC off 11 Module AC trouble Module AC on Module AC off 12 Auxiliary power trouble Auxiliary power OK Auxiliary power trouble 13 Main battery trouble Main battery(s) OK Main battery(s) low 14 SnapCard battery trouble SnapCard battery(s) OK SnapCard battery(s) low 1 Module battery trouble Module battery OK Module battery(s) low. : If no LEDs are on, either the group is not programmed or the partition/area is not enabled. 100

103 Appendix B: Reference Tables Smoke and Heat Detector Installation Smoke and heat detector installation must adhere to the following diagram: 0 = * H * H J= EHM A BBE? A 0 = BBE? A EL E C, E E C 4 4 BBE? A 0 = BBE? A ) I A JA? J H I D > A? = A =? D A L A * = I A A J > > O J= EHM A, E E C 4 EJ? D A 0 EL E C 4 * H * H 0 = * H A JA? J H I I D > A? = > A JM A A JD A I A A F E C = H A = JD A H A I J BJD A B= E O EL E C K EJ BBE? A BBE? A A I EA I BBE? A + I A J - A L = J H BBE? A 0 = BBE? A + BA HA? A * H, E E C 4 EL E C 4 EJ? D A 0 * H * H 1 B= E O EL E C K EJI M EJD H A JD = A I A A F E C = H A =? = JA = I A JA? J H = JA =? D = H A = 1? A H? E= F H F A H JEA I = I A JA? J H I D > A? = E A =? D H A E E C K I A JA? J H I I D > A? = E JD A? A JA H BJD A H H D = H J A I I JD = " E? D A I BH JD A M = 9 D A JD A JA? J H EI K JD A M = JD A J F BJD A JA? J H I D > A " J E? D A I BH JD A? A E E C, JE I J= I A JA? J H I M D A H A H = = > EA JJA F A H = JK H A I = H A = > L A H > A M " ) J? = A JA? J H I E BH J B) + 0 A = J H A C EI JA H I H JD A H? = JE I M D A H A H = = EH? EH? K = JE M E A A F I A BH A JA H E C JD A JA? J H 6 EJE = E B H = JE D K I A BEH A M = H E C EI = L = E = > A = J E =? I JBH 6 D A = JE = EH A 2 H JA? JE ) I I? E= JE * = JJA H O = H? D 2 = H 3 K E? O ) $ ' 4 A G K A I J = 2 ) % " 4 A G K EH I A JA? J H 0 0 A = J@ A JA? J H A JA? J H EI F JE = EB@ H EI JF H L E@ > A JM A A > = I A A H A? H A = JE H I & # # % C $ I B 101

104

105 * / ; ), ) * 7 4 / ) 4 ; ), 0 - ) 8 1/ ) 6 4 ; 6 - $ # $ $ # $ " ), $ # $ $ # $ # " 8 ) + " 8 ) + /, : , + * / ) , +! " # $ % 1+ /, ` - +, ) 4 ; * * 4 - ) ) / / 4 - -! " # $ % & '! " # $ % & ' ), ) " 8 ) + 8 ) $ &! ) + $ ), ) " 8 ) + 8 ) $ &! ) + $ ) 1 6 -, ) 4 1 /, 1 ) 4 1 / - ; ) / 4 7, 0 ) 4, : * ) + 4 -, - & ) - 4! $ # 9 ) 6 6 4! $! 9 ) ) 1 6 -, 2 ) - + ) * ) ) ; + -, * ) + " ' " $ % + ) 6 - ) 6, # 4! # 8 + ) 2 ) ) 4 1 -, % + ) 6 - ) 6, & ) ) 4 ) - " * ) 2 0 ) ), $ &! $ & " ' , " ' " $ % + ) 6 - ) 6 ) 6, , " ' " $ % + ) 6 - ) 6 ) 6, ; , 4 ) ; + -, ) * ) + " ' " $ % + ) 6 - ) 6 ) 6, ) * / 0 ) 4 - " ' " $ - " ' " $ % ), / 0 ) 4 - " ' "! 6 7 -, , 4 ) ; ) ) 4 ) - * ) + /, * 7 * / * 7 ) 4 -, 8, + " 6 -! 1 6 -, , , + ) ) : * ) + " ' " $ % + ) 6 - ) 6 ) 6, ),, 16 1 ) 1 6 -, * ), ), 4, # 1 6 -, ) 6, ` `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